How to coat DNA probes on the nylon strips?

11 November 2018 0 10K Report

For hybridization of DNA product and probes need to coat probes on the nylon strip.

Badges
Science topic

More Farzad Sadri's questions See All

Which concentration of herbal extract (in mg/ml) often use to evaluate antimicrobial activity? and which range of concentration usually applied?

I should say, in our research group work on evaluate herbal extract we could not solve extract in more than 10mg/ml (with low concentration of DMSO

08 September 2018 8,626 3 View

How can report minimal inhibitory concentration (MIC), when you will count MIC of herbs extract?

we are looking for the new methods of MIC in our group

04 May 2017 2,965 4 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Z-average size from Dynamic Light scattering can it be lower than the original probe size?

Hi everyone, Recently I have been conducting Dynamic Light scattering experiments in a micellar solution at 5 and gel at 37 degrees of Celsius with latex particles of diameter 190-500 nm. While...

01 August 2024 1,168 4 View

Dimensions of an MJ Research 96-well alpha module?

Can anyone with an MJ research / BioRad PCR machine from ~2010 or earlier tell me the external measurements (LxWxH) of the removable standard PCR alpha modules that can be removed from a PTC200 or...

30 July 2024 2,867 0 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Is it necessary to attach fluorophore at 3' end in MIC RT PCR machine for Dual hybridization Probe designed especially for genotyping assay?

I designed 2 dual hybridization probes for my single SNP. where I attach my fluorophore 5'-FAM-nnnn-BHQ1-3', and 5'-HEX-nnnnnn-BHQ2-3'. I need to run it on the MIC RT PCR machine by Biomolecular...

28 July 2024 5,658 0 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View