How to calculate Transport properties using impedance spectroscopy for polymer nanocmposites?

More Chetan Chavan's questions See All

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Abdelkader BOUAZIZ

Dear Chetan Chavan, the technique is widely used. The following documents show exemples of its application. My Regards

https://doi.org/10.1016/j.ssc.2020.114012

https://www.researchgate.net/publication/259270888_A_method_based_on_impedance_spectroscopy_to_determine_transport_properties_of_polymer_electrolytes

https://doi.org/10.1002/pc.21236