How to calculate the transition and transvertion ratio seperately by using mega

06 June 2017 1 10K Report

how to calculate the transvertion ratio by using mega

As per MEGA, rates of transitional substitutions are shown in BOLD, transversional substitutions in ITALICS.

But if you still find it tough to get the results as per you, then check online softwares. You can easily retrieve your data there. Good luck.

Badges
Science topic

More Ramandeep Achint's questions See All

What is the basic difference between DNA extraction and DNA isolation?

DNA extraction/ DNA isolation

11 December 2017 5,580 0 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View

Using the Pfaffl method: Is it possible that the ratio of the calibrator does not equal 1?

Hi all, I have a question regarding calculations using the Pfaffl method. I have 3 groups per experiment: 1 control group (calibrator) and 2 treatment groups with 6 to 7 biological repeats per...

19 February 2021 8,351 2 View

ZnS oxidizes to ZnO!!why??

when I put my ZnS solution in the chemical bath, the ZnS oxidizes so there are ZnO peaks appearing because of the reaction with the oxygen in the air, despite the fact that I close the beaker...

14 February 2021 5,778 9 View

Xrd result of ZnO thin film shown better crystallinity at low temperature and the crystallinity decreases as the temperature increased. why?

I have synthesized ZnO thin films at four different substrate temperature say, 300, 350, 400 and 450C. and the samples were annealed at 450C for half an hour. the xrd result shown better...

04 February 2021 7,641 4 View

How to form a shell around a nanostructure core in solution phase synthesis?

Hey, I want to know if I have fabricated some nanostructure and further I want to make a shell on the nanostructure by solution phase method by making it core-shell nanostructure. So, anybody can...

01 February 2021 9,966 4 View

How to calculate radial distribution function (RDF) of a complex from Ab initio MD simulation trajectory?

Hi all, Is there any software or webserver to read the molecular dynamics (MD) simulation trajectory which obtained from Ab initio MD simulation to calculate the atom-atom radial distribution...

25 January 2021 9,474 3 View

Solving diffusion- reversible chemical reaction equation: How to solve both terms numerically?

I am using finite difference method to discretize the parabolic equation (explicit method), but confused about the chemical reaction term. Solving the generic equation for i specie involves a...

24 January 2021 1,149 18 View

Doubt in DFT geometry preparation?

Hi all, I am trying to perform some ab inito DFT calculations using cp2k code. I have a unit cell of 120 atoms and would like to know how to refine or reduce the number of atoms in the unit cell...

20 January 2021 6,024 3 View

Why it is required to optimize a unit cell generated from cif lattice parameters and atomic coordinates during ab initio solid state calculations?

A cif file represents a unit cell with minimum energy. My question is, in the start of any ab initio calculation for unit cell generated from the cif file, why we are advised to optimize cell...

19 January 2021 9,883 3 View