How to calculate the serpentinization degree % in the serpentine?

Mostafa Abdel azim Masoud @Mostafa_Masoud2

09 September 2018 0 644 Report

I want to calculate the degree of serpentinization in more than one type of serpentine

Badges
Science topic

More Mostafa Abdel azim Masoud's questions See All

What it is the difference between Laccase enzyme and Lignin degrading enzyme?

What it is the difference between Laccase enzyme and Lignin degrading enzyme

31 December 2018 10,027 0 View

How to calculate the percentage of atomic composition for concrete ?

I want to to calculate the percentage of atomic composition for concrete like that: H=2, O=50, Na=15

11 December 2018 4,970 3 View

There are any ASTM or British standards of porosity measurement for the hardened concrete?

I have searched about any standards of porosity measurement for the hardened concrete, but I didn't find any thing.

08 September 2018 3,350 3 View

Until now there are not any papers explaining the relation between crushing value of aggregate and compressive strength of concrete, I'm right?

I didn't find any papers explaining the relation between crushing value of aggregate and compressive strength of concrete

05 June 2018 2,347 15 View

Are there any suggestions for references about the relation between porosity and void ratio in concrete?

I want references about the relation between porosity and void ratio in concrete.

04 May 2018 5,441 6 View

What is the interpretation of presence of CH3 functional group in the IR ?

what is the interpretation of presence of CH3 functional group in the IR in treated silicate material with NaOH although the ore (original material before treating) did not contain any carbon ?

03 April 2018 6,745 6 View

Are these ingredients of concrete indicated right?

This is an SEM image of concrete and I want to know if I indicated the components right or wrong?

03 April 2018 1,009 0 View

Is the aggregate crushing value (ACV) test is a an indicating method for aggregate strength?

I want papers about ACV is indicating method for aggregate strength

01 February 2018 5,270 7 View

There is a calculation method for finding the the void ratio knowing the porosity and water absorption in concrete?

I want to theoretically calculate the void ratio knowing the porosity and water absorption?....except for ASTM CODES?

01 February 2018 4,049 0 View

Is it possible for turquoise to have a violet color?

Turquoise has a blue and green colors, but I see some have a violet and other colors, so it is possible ?

31 December 2017 5,255 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

Has anyone used the Illumina ITS1 primer sets?

Hi everyone, Illumina provides a list of primers to amplify with high taxonomic coverage the ITS1 region for further fungal sequencing, but I cannot find the exact amount necessary of each...

25 February 2021 6,969 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View

What is the better software for approximation of 3D surface with equations?

I have a massive of x, y, z coordinates of 2D surface in 3D space, which builded in Ansys HFSS or AutoCAD. How can I get the analitical aproximation of this surface by formulas?

21 February 2021 3,444 7 View

Using the Pfaffl method: Is it possible that the ratio of the calibrator does not equal 1?

Hi all, I have a question regarding calculations using the Pfaffl method. I have 3 groups per experiment: 1 control group (calibrator) and 2 treatment groups with 6 to 7 biological repeats per...

19 February 2021 8,351 2 View

How can we assess applied digital skills and soft skills through online examinations during COVID-19 semester?

The final qualification assessment for major programs is a strict regimen that involves different stages - oral and written exams, final project viva, internal and external review. How are ICT...

16 February 2021 1,762 8 View

How to compare different models with different inputs and data length?

I want to run 5 different models to estimate stream flow. In order to optimize the characteristics of these models I use Taguchi method. So I have to run different models according to the Taguchi...

11 February 2021 7,986 6 View

How do you obtain ASI (Annual Survey of Industries) plant identifiers, to create a panel data?

Dear all, Is there anybody who has worked with ASI (Annual Survey of Industries) Firm-Level data? I have extracted the data files with STATA, and now I need help with creating a panel for...

11 February 2021 876 4 View