How to calculate the power requirement for a vertical axis mixer handling grains?

14 October 2022 0 5K Report

The vertical axis mixer/agitator is provided to a hopper system to constantly agitate the material and prevent it from bridging. What are the considerations that needs to be taken? Any reference will be greatly appreciated. Thank you

Badges
Science topic

Similar topics
Correction

More Ashish Jose M's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

Why do open and free science in a world where science is not open and free?

Because I have realized that the world tends more and more to do open and free science and there is a trend more and more to choose free databases, free tools and open access platforms.

01 August 2024 10,046 1 View

What is the relationship between the threshold voltage and the device's noise performance, particularly in terms of flicker noise and thermal noise?

The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...

29 July 2024 3,246 0 View

Should Coefficient of Variation (CV) in a biological data necessarily be below 30%?

In a research, lesion diameter due to a disease has a CV below 10%. However, in an another parameter, disease inhibition percentage (compared to control), a value derived from lesion diameter...

27 July 2024 201 0 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

Comparison of Methanol and ethanol treatment on collagen based scaffolds?

Kindly share a research paper that explains the effect of Methanol and ethanol treatment on collagen based scaffolds. How it increases porosity and swelling. Kindly help me find a paper. Thank you

24 July 2024 3,937 0 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

How to represent Annexin V apoptosis study data in publications?

Hi, I have performed an Annexin V apoptosis study using flow cytometry and got quite good results. I doubt how to represent the quadrant percentages in the final bar graphs. Some papers only show...

13 July 2024 356 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How to isolate lymphocytes from mouse spleen?

I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...

04 August 2024 9,913 7 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

How to know the b axis of a single crystal?

How to apply magnetic field parallel to b axis of any crystal

29 July 2024 4,083 2 View

MAGeCK Plotting Error: Logarithmic Axis Must Have Positive Limits?

I have been running a MAGeCK test command on the terminal for a CRISPR screen to rank sgRNAs and genes based on the read count tables. However, I get only the plot of the top-ranked genes...

28 July 2024 9,811 1 View

How can I define Planetary motion in ABAQUS CAE, how define motion of three rollers around a central axis and passive rotation about their own axis?

16 July 2024 4,145 1 View

Is there anything faster than Xarray or Pandas out there?

Hello, dear RG community. Personally, I have found Xarray to be excruciatingly slow, especially for big datasets and nonstandard operations (like a custom filtering function). The only suggestion...

15 July 2024 4,705 2 View

I came across oscillations in a pressure profile for a pipeline flow along the axis of a cylinder, how do I prove that these are not numerical err?

In terms of CFD, we often analyze the stability of the error using Von-Neumann analysis, especially for FDM based problems. Should we follow the same approach for a compressible fluid flow using FVM ?

13 July 2024 6,296 5 View

What are the potential environmental risks associated with improper handling and disposal of digestate, and how can they be mitigated?

What are the potential environmental risks associated with improper handling and disposal of digestate, and how can they be mitigated? Let us see what are the ways and how to avoid them as...

11 July 2024 2,045 0 View