How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Mixed ANOVA or Multilevel modeling?

Hi everyone, I'm having some questions about choosing the right test for my experiment and I hope I can find help here! Here are the settings of the experiment: 1. participants are randomly...

14 February 2021 1,028 4 View

What is the method of removing RNase contamination from a filter paper surface?

I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...

12 February 2021 3,926 3 View

How to do variation partition for a distance matrix for microbial ecology?

I have bacterial, fungal, and protist OTU table. I want to know to what extent protist and fungi distribution can explain the bacteria distribution. I only know Mantel test could do a correlation...

11 January 2021 4,164 2 View

Are there any method to detect implanted stem cells?

Dear, We developed a microcarrier that was pre-seeded hUC-MSCs to repair a rat bone defect. However, we didn't use GFP or Luciferin to track cell survival. If there's any way to identify the...

15 December 2020 6,065 3 View

Did anyone do microglia Oil Red O staining?

I need to stain adiposome in microglia, but I don't know how to confirm that are really success? method : Removed media and washed cells with PBS, then added 4 % paraformaldehyde for 20 minutes at...

24 November 2020 2,359 2 View

How to characterize the dispersion of aluminum oxide in Al matrix composite which reinforced by alumina during the powder metallurgy?

Now we could characterize the disperion of Al2O3 in AMCs (pure Al reinforced by Al2O3 ) after sintering. But the process of powder metallurgy has a lot of steps, which take long time. The cycle...

08 November 2020 5,244 3 View

Is that possible the filter of flow cytometry was failed so I got those data using FL1 vs FL2 and FL1 vs FL3?

The cells were expressing GFP and also incubated with PI for dead cells detection. This is my first-time using this BD Accuri C6 and I'm not sure if I need to set compensation (I tried to follow...

01 November 2020 8,360 3 View

How do I solve "unrecognized in LdAtmC" of Gaussian 16 l301.exe type error?

Hello, I have trouble with transitional state calculation in gaussian 16 program. I started with the first frequency calculation with cartesian coordination and it ends up normally. the input...

15 October 2020 1,498 1 View

How to heat a reactor up to 900C?

I'm taking a bachelor design, I'm supposed to maintain an endothermic reactor at 900C and 30 bar. The typical jacketed reactor is not really feasible and I'm thinking of fired heater to maintain...

07 October 2020 8,558 5 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

What could be reason for getting such type of graph for complex impedance in case of polymer blend films?

Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?

26 February 2021 3,487 3 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

What is the system of units used in the thermal conductivity by Spitzer and Harm?

23 February 2021 9,253 1 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

What is the difference between AC conductivity and DC conductivity? Is AC conductivity = ionic and DC conductivity = electronic?

I am reading papers on batteries and although mostly people have reported ionic conductivity in Scm-1 but some have reported DC conductivity as well I and am confused as to what that is. Any help...

21 February 2021 9,207 6 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View