hydraulic forging press of 400 ton capacity required how much quantity oil. all the other parameters are known.
hi abdul,
there are basically three type of flows to consider,
- displacement flow = cylinder velocity times cylinder area
- compression flow = ammount of oil to raise pressure to force/cyl area required. the attached volume plays a crucial part here
- leackage flow = volumetric losses of drive train under pressure
sum of the above gives you the total required flow.
you can compute by hand or use a hydraulic simulator tool. bosch rexroth offeres one for free. check it out at www.boschrexroth.com/simster
good luck
m. liedhegener
bosch rexroth ag
I want to know the reason for the impression as shown in figure after hot forging of composite material. I have done a step wise hot forging of cylindrical shape ingot and after hot forging the...
09 October 2018 3,045 13 View
i want to know the advantages & disadvantages of mechanical (specifically sand blasting) & chemical finishes. The end product for finishing is composite sheet as well as ingot having main...
06 July 2017 2,555 4 View
i want to forge a circular billet in to a rectangular bar (figure and dimensions are attached in doc) using open die hydraulic press forging . Can any one guide me what should be the design of Die...
31 December 2016 4,189 5 View
i want to calculate the required cooling water flow rate by using heating power and maximum temperature in the chamber. The heating mechanism is resistance heating and inlet temp of water is 20...
09 October 2016 7,523 0 View
which type of shot (balls) will be used in shot blasting of sheet made up of Composite((Aluminum alloy +boron carbide composite) or for (Aluminum alloy +silicon carbide composite)
06 July 2016 9,899 1 View
generally mixtures of HCl and HNO3 (20–50%) is recommended for washing the alumina but using that small cracks form on surface of tube which can be opened later. can anyone suggest the washing...
01 February 2016 8,737 4 View
I have work piece of metal to forge in hot forging process. The dimensions of work piece before and after is given. I want to calculate how much load is required in to deform the work piece to...
11 December 2015 4,958 5 View
For example if concrete have E= 200 Mpa and Rebars have 500Mpa then how to find the Modulus (E) and other properties of the re- in forced concrete?
05 June 2015 6,262 0 View
05 June 2015 1,448 7 View
i have to model vicker indentation process in which i have to make indent on the plate can any one help out me how to model it??
03 April 2015 7,176 2 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...
07 August 2024 2,569 1 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to know how do you make real time pcr solation ? is there any machine to make it? thanks for answering
05 August 2024 1,660 0 View
I´ve been unable to find specific information about this neurotrophin in the CNS of rabbits exclusively. There is extensive info in mice, fish and rats, but in brain´s rabbit is hard to find....
04 August 2024 762 1 View
I want to know more about petroleum deposits in Iran.
02 August 2024 8,725 3 View
Hi I am working on data driven model of the microgrid, for that, i need the reliable datasets for the identification of MG data driven Model. Thanks
02 August 2024 5,748 4 View
I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?
02 August 2024 3,143 4 View