How to Calculate Nortons Creep Constants from Time-Deflection Graph?

Joshua Davies @Joshua-Davies-23

05 April 2023 0 369 Report

Hello all,

Could someone please advise on how to calculate the 3 creep constants for the Norton Bailey creep law in ansys?

I have experimental data in the form of a time/deflection graph attached.

Thank you in advance.

Badges
Science topic

Similar topics
Mathematics

More Joshua Davies's questions See All

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Culture plates for PBMC (non-adherent). For infection?

Hello, good morning. I would like to know which plate I can use to infect fresh PBMC with virus and culture for 24 hours. I have tried using 12-well and 24-well plates, but many cells adhere and...

24 July 2024 2,158 2 View

How to removal of dead cells and debris from organoid cultures?

I'm currently working with human pancreatic organoids and I am wondering to remove the dead cells and debris from health organoids, any suggestions would be appreciated!

17 July 2024 8,330 1 View

Cp of Turbine is ever increasing with Tip Speed Ratio. What Could be the reason??

I am a student of Mechanical Engineering. I am doing CFD opf Archimedes Winf Turbine. I am trying to validate the result of Paper. But the problem is that tha value of Power Coefficient is ever...

05 July 2024 6,839 2 View

Does the temporal summation of EPSPs accumulate linearly to action potential threshold or logarithmically to a plateau/limit?

I am attempting to determine which current inputs (in uA) are subthreshold for inducing a burst of activity. This is because I am attempting to model DBS form epilepsy in vitro, which clinically...

23 June 2024 4,083 1 View

Why our eyes can concisely definite left and right, high and low? But cannot near and far?

While analyzing the data of point cloud, i found some strange phenomenon about the precise. But I expect there is no best plan between LiDAR and binocular vision. However, why our eyes more...

21 June 2024 5,269 3 View

How to avoid metal contamination from a sonicator?

Hi, I have been using a Q-Sonica Q500 Sonicator to disperse samples on nanocellulose and make emulsions. I have notices black dust like particulates settling out in some samples and on the bottom...

12 June 2024 9,737 6 View

Can anyone send me the Weblink to Download ECRTool?

ECRTool is a Matlab based software tool for plotting Electrical Conductivity Relaxation graphs.

04 June 2024 8,133 1 View

What would be the safety of our roads be with the autonomous vehicles ?

safety of autonomous self-driving vehicles.

26 May 2024 6,880 1 View

What should the phase and pulse duration be for deep-brain stimulation (DBS) for epilepsy?

In DBS settings, I have seen stimulus widths of up to 500 us in duration; however, the most common pulse duration seems to be between 90-150 us. Clinically, mono- or bi-polar electrodes can be...

26 May 2024 5,819 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

There is possible way to calculate experimental DOS from the UPS spectrum of the material. How to calculate the DOS from UPS?

Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.

29 July 2024 4,971 1 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Critique Calculaltion in Topological Indices and QSPR Modeling?

The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...

24 July 2024 9,644 1 View

How to do calculation of Louvain methods calculation for excel sheet and and is there any software available?

The Louvain method – named after the University of Louvain where Blondel et al. developed the algorithm – finds communities by optimizing modularity locally for every node’s neighborhood, then...

23 July 2024 6,659 0 View

Is there a name for this type of function?

Let n∈ℕ, where the function f:A⊆ℝ𝑛→ℝ, 𝐴 is Borel, and (A,d) is a completely seperable space. What is the name of the functions where the graph of f in any (n+1)-dimensional box of A×ℝ is...

17 July 2024 258 1 View