02 June 2017 1 751 Report

How to calculate mass transfer coefficient and axial dispersion coefficient.

when only following parameters are known

1.Bed height

2.Flow rate

3. Inlet adsorbate conecntration

4. External mass transfer coefficient ?

More Renu Bisht's questions See All
Solvent extraction post-crude oil degradation study?

In my current research, I am investigating the characterization of bacteria capable of degrading crude oil. The quantify the crude oil degrading ability of the bacteria, the existing protocol...

11 April 2024 6,686 3 View

Restriction digestion and ligation , both should be of same company ?

Can any be from a plant background? i want to know that for digesting the vector and ligating the insert into the digested vector, is it crucial that we use chemicals from the same company as the...

21 March 2024 1,343 1 View

I am doing TA cloning, and i do not get fall out after the restriction digestion. what is its probable reasons?

After transformation in DH5 alpha, I got positive colonies. I have confirmed it by PCR (using an isolated plasmid of positive colonies as a template to run PCR by Takara Taq) and restriction...

14 March 2024 3,786 7 View

How can we calculate shear rates on each slip system in DAMASK ?

I use the phenomenological model for the crystal plasticity simulations, where the shear strain can be taken as output. However, I require the shear strain rate on individual slip planes to...

08 March 2024 649 1 View

How can strain-controlled cyclic loading be simulated in DAMASK ?

I have simulated the stress-controlled cyclic loading in DAMASK. However, I am having difficulty setting up the load-case file for strain-controlled cyclic loading between two given strain levels.

19 October 2023 9,772 1 View

What is the Margalef diversity index, and how does it differ from other common diversity indices used in ecological research?

2. In forest ecology studies, for which types of samples or datasets is the Margalef diversity index most applicable? Are there specific scenarios where it is particularly informative? 3. When...

12 October 2023 7,527 0 View

Why there is error in installation of Boltztrap?

Hello everyone, I am trying to install boltztrap with a quantum espresso interface for doing thermoelectric properties. For this I have gone through various Boltztrap tutorial. I have...

07 October 2023 834 2 View

Likert scale data analysis and multi-level linear regression adequacy for this data type?

Dear all, I have the following data and questions related to the issues in the results. Independent variable I did an online survey and asked parents questions about neighbourhood-built...

26 September 2023 4,919 4 View

Can someone help me in CAD detector troubleshooting?

The CAD detector is not working properly. Could someone explain why that be the case? or the ways to try to troubleshoot it.

17 September 2023 771 1 View

Why do some researchers utilize soil extract a medium for culturing soil bacteria and some do not?

I have been researching about bacterial isolation from petroleum\crude oil contaminated soil samples. While reading the papers, I seem to notice that everyone has a different approach for...

13 August 2023 3,807 0 View

Similar questions and discussions
Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

How can I define dispersion for salt in CMG or Eclipse?

How can I define dispersion for salt in Eclipse in a low salinity water flooding code? how can I active interactions between tracer and polymer in Eclipse? Please let me know if you have any idea.

05 August 2024 1,218 1 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

Where to find a gene list for CRISPRa/i library screening of regulatory factors that affect pathogenic Th17 differentiation in PBMC?

I want to perform a CRISPRa/i library screening for candidate regulatory factors that affect pathogenic Th17 differentiation in PBMC. But I am wondering how to define the size of gene library, so...

31 July 2024 2,150 0 View

Hello dear researchers. I would like to know what is a normalized mass in an EDX analysis?

EDX analisys

31 July 2024 5,947 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close