How to calculate Kc in deltaG = -RT lnKc where kc=Ca/Ce?

01 January 2017 0 9K Report

how to calculate Kc in deltaG = -RT lnKc where kc=Ca/Ce ? Where Kc is apparent equilibrium constant (Kc) of the adsorption.

if for a particular temperature i have 5 values of C initial (without adsorbent) and C final (with adsorbent) then how i will calculate one value of Kc.?

Badges
Science topic

More Renu Bisht's questions See All

I have determined maximum wavelength of my dye wastewater. How to determine intial cocentration of dye wastewater and name of dye in it?

i have determined maximum wavelength of my dye wastewater. How to determine initial concentration of dye wastewater and name of dye in it?

05 June 2018 6,849 6 View

Kindly suggest few models which are best and simple for fixed bed column study?

08 September 2017 827 1 View

How to calculate external mass transfer coefficient for fixed bed column filled with the adsorbent pellets?

How to calculate external mass transfer coefficient for fixed bed column fiiled with the adsorbent pellets?

07 August 2017 9,207 3 View

How to contact googlescholar for wrong citation?

05 June 2017 2,985 7 View

How to calculate mass transfer coefficient and axial dispersion coefficient?

How to calculate mass transfer coefficient and axial dispersion coefficient. when only following parameters are known 1.Bed height 2.Flow rate 3. Inlet adsorbate conecntration 4. External mass...

05 June 2017 6,679 1 View

Continous column adsorption capacity

If i am working on a column filled with adsorbent, in my batch study max adsorption capacity was achieved in 1 hr. In continous column how can i achieve that max adsorption capacity that was...

05 June 2017 4,279 7 View

Does anyone have any experience with "Environmental Engineering and Management Journal" with ISSN 1582-9596 and IF - 1.008.

Does anyone have any experience with "Environmental Engineering and Management Journal" with ISSN 1582-9596 and IF - 1.008. On their website they instruct to mail your research paper directly on...

05 June 2017 8,527 0 View

In my model of matlab for fixed bed adsorption column, i have obtained very large time in X-axis of breakthrough curve?

In my model of matlab for fixed bed adsorption column, i have obtained very large time in X-axis of breakthrough curve..i.e nearly 5*10^(5) second. Is it possible? why it is higher. please suggest?

04 May 2017 1,314 4 View

How to measure adsorbent surface area?

I have used BET to determine surface area of my adsorbent (cellulosic material) but nitrogen does not adsorb on its surface. Only one point is available. Please suggest how can i measure its...

04 May 2017 6,204 3 View

How to make pellets of acid treated wheat bran . It is similar to activated carbon?

How to make pellets of acid treated wheat bran ? It is similar to activated carbon..we made pellets using pelletizer using clay as a binder..pellet is perfectly made but after dipping in water it...

03 April 2017 218 0 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View

Using the Pfaffl method: Is it possible that the ratio of the calibrator does not equal 1?

Hi all, I have a question regarding calculations using the Pfaffl method. I have 3 groups per experiment: 1 control group (calibrator) and 2 treatment groups with 6 to 7 biological repeats per...

19 February 2021 8,351 2 View

How to calculate radial distribution function (RDF) of a complex from Ab initio MD simulation trajectory?

Hi all, Is there any software or webserver to read the molecular dynamics (MD) simulation trajectory which obtained from Ab initio MD simulation to calculate the atom-atom radial distribution...

25 January 2021 9,474 3 View

Solving diffusion- reversible chemical reaction equation: How to solve both terms numerically?

I am using finite difference method to discretize the parabolic equation (explicit method), but confused about the chemical reaction term. Solving the generic equation for i specie involves a...

24 January 2021 1,149 18 View

Doubt in DFT geometry preparation?

Hi all, I am trying to perform some ab inito DFT calculations using cp2k code. I have a unit cell of 120 atoms and would like to know how to refine or reduce the number of atoms in the unit cell...

20 January 2021 6,024 3 View

Why it is required to optimize a unit cell generated from cif lattice parameters and atomic coordinates during ab initio solid state calculations?

A cif file represents a unit cell with minimum energy. My question is, in the start of any ab initio calculation for unit cell generated from the cif file, why we are advised to optimize cell...

19 January 2021 9,883 3 View

Is it possible to calculate entalphy of LiBr/H2O or another solution if we know correlation of specific heat without using any software?

17 January 2021 5,522 3 View

What does a negative real part of impedance indicate in a Nyquist plot?

I am trying to quantify Parylene C's hermetic encapsulation quality using EIS with a 2 electrode configuration (WE/WS and RE/CE). I am simply using two patterned gold layers on glass as my...

12 January 2021 7,399 14 View

What is the best way to calculate electrical conductivity of semiconductors and the same system with a layer of oxide using Quantum Espresso?

I have tried BoltzTrap, and EPW but I'm not sure whether Boltzmann Transport Equation is a right approach for a complex system (semi cond. + an Oxide layer or even the semiconductor itself). Also...

11 January 2021 4,597 4 View