How to calculate mass transfer coefficient and axial dispersion coefficient?

Renu Bisht @Renu_Bisht2

06 June 2017 1 7K Report

How to calculate mass transfer coefficient and axial dispersion coefficient.

when only following parameters are known

1.Bed height

2.Flow rate

3. Inlet adsorbate conecntration

4. External mass transfer coefficient ?

Adel Oueslati

Dear Renu Bisht,

Your question is easily to solve. i recommend for you the following books titles:

1) Raffinage et génie chimique. Wuitier. (Frensh language)

2) Coulson & Richardson’s CHEMICAL ENGINEERING VOLUME 6 , Fourth edition

Chemical Engineering Design, R. K. Sinnott. (Enlish).

Best wishes!

kind regards!

Badges
Science topic

More Renu Bisht's questions See All

I have determined maximum wavelength of my dye wastewater. How to determine intial cocentration of dye wastewater and name of dye in it?

i have determined maximum wavelength of my dye wastewater. How to determine initial concentration of dye wastewater and name of dye in it?

05 June 2018 6,972 6 View

Kindly suggest few models which are best and simple for fixed bed column study?

08 September 2017 943 1 View

How to calculate external mass transfer coefficient for fixed bed column filled with the adsorbent pellets?

How to calculate external mass transfer coefficient for fixed bed column fiiled with the adsorbent pellets?

07 August 2017 9,319 3 View

How to contact googlescholar for wrong citation?

05 June 2017 3,126 7 View

Does anyone have any experience with "Environmental Engineering and Management Journal" with ISSN 1582-9596 and IF - 1.008.

Does anyone have any experience with "Environmental Engineering and Management Journal" with ISSN 1582-9596 and IF - 1.008. On their website they instruct to mail your research paper directly on...

05 June 2017 8,645 0 View

Continous column adsorption capacity

If i am working on a column filled with adsorbent, in my batch study max adsorption capacity was achieved in 1 hr. In continous column how can i achieve that max adsorption capacity that was...

05 June 2017 4,398 7 View

In my model of matlab for fixed bed adsorption column, i have obtained very large time in X-axis of breakthrough curve?

In my model of matlab for fixed bed adsorption column, i have obtained very large time in X-axis of breakthrough curve..i.e nearly 5*10^(5) second. Is it possible? why it is higher. please suggest?

04 May 2017 1,547 4 View

How to measure adsorbent surface area?

I have used BET to determine surface area of my adsorbent (cellulosic material) but nitrogen does not adsorb on its surface. Only one point is available. Please suggest how can i measure its...

04 May 2017 6,423 3 View

How to make pellets of acid treated wheat bran . It is similar to activated carbon?

How to make pellets of acid treated wheat bran ? It is similar to activated carbon..we made pellets using pelletizer using clay as a binder..pellet is perfectly made but after dipping in water it...

03 April 2017 340 0 View

How to wash and dry chitosan coated powdered adsorbent which is in form of a slurry?

How to wash and dry chitosan coated powdered adsorbent which is in form of a slurry ? It is in form of a gel, how to wash it and dry?

01 February 2017 9,076 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

How can I define dispersion for salt in CMG or Eclipse?

How can I define dispersion for salt in Eclipse in a low salinity water flooding code? how can I active interactions between tracer and polymer in Eclipse? Please let me know if you have any idea.

05 August 2024 1,218 1 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

Where to find a gene list for CRISPRa/i library screening of regulatory factors that affect pathogenic Th17 differentiation in PBMC?

I want to perform a CRISPRa/i library screening for candidate regulatory factors that affect pathogenic Th17 differentiation in PBMC. But I am wondering how to define the size of gene library, so...

31 July 2024 2,150 0 View

Hello dear researchers. I would like to know what is a normalized mass in an EDX analysis?

EDX analisys

31 July 2024 5,947 2 View