How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

THENNAVARAJAN SUBRAMANIAN @Thennavarajan-Subramanian

23 February 2021 1 6K Report

Hello,

You can use the Fluid-Shell Interaction multiphysics interface to model phenomena where fluid and a deformable structural shell affect each other. Another way, depending on your structure use the Fluid-Membrane Interaction multiphysics interface to model phenomena where a fluid and a deformable membrane affect each other.

Regards

Badges
Science topic

More THENNAVARAJAN SUBRAMANIAN's questions See All

How to find intensity of research and technology outcomes from the reputed journal paper? Either by research or technology or by both of them?

22 February 2021 5,525 3 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

H2/CO ratio calculation in dry reforming?

How to calculate H2/CO ratio in dry reforming? This question is for my friend. The ratio should come around 1.0. But the ratio coming 35, 40, 48. CO peak is higher and H2 peak is smaller. What is...

31 January 2021 7,788 3 View

Can anyone suggest which type of sensor input signals are more critical in flying aero engines for on-board diagnostics?

Can anyone suggest which type of sensor input signals are more critical in flying aero engines for on-board diagnostics? and high potential sensors for prognostics?

18 January 2021 4,087 1 View

How to build aero engine fuel system online prognostics simulation model using Matlab, Simulink and Simscape?

17 January 2021 5,181 1 View

How to predict remaining useful life (RUL) on used aeroengine and its components level?

How to predict remaining useful life (RUL) on used aeroengine and its components level? (or) Any standard mathematical relations for RUL?

17 January 2021 8,127 3 View

For dissolving haloalkanes which is best solvent - polar or nonpolar?

For dissolving haloalkanes which is best solvent - polar or nonpolar? How much quantity of solvent is required if the solublity is unknown.

12 October 2020 3,447 4 View

Why the color of dichloropropane changed?

The color of dichloropropane changed from colorless to brown color during distillation. The actual color of dichloropropane is colorless. Why the color changed. Thank you

27 September 2020 3,216 3 View

Conversion of Dichloroalkane into Alkanediols?

I need to convert 1,2-dichloralkane to alaknediol using reflux condenser. The dichloroalkane is insoluble in water. Hence i need to take methanol/ethanol as solvent. For substitution reaction i...

14 September 2020 6,292 3 View

How do you exactly determine the annealing temeperature while splicing two gene sequences in the first annealing cycle of overlap extension pcr?

In OE PCR, I have to stitch two gene sequences, so the annealing temperature in the first cycle would depend on the overlap reagion between two products designed with appropriate primers or would...

14 March 2020 2,639 3 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View