How to add zero length elements in GiD?

08 August 2018 0 5K Report

While modelling an interface in GiD+Opensees, how to add zero length elements (springs)?

Badges
Science topic

Similar topics
Engineering
Modeling

More Suvendu Kumar Sasmal's questions See All

Which geotechnical engineering journals accept review papers?

Which geotechnical engineering journals accept reveiw articles. please provide the list. Does "Journal of earthquake engineering" accept review articles?

01 February 2018 3,294 0 View

How to determine natural frequency of a foundation system?

What are the experimental/numerical procedure to determine the natural frequency of a shallow foundation system? what are the ranges for foundation resting on granular soil?

11 December 2017 6,169 3 View

How to plot a graph between Number of cycles of load versus settlement of shallow foundation using OpenSEES?

Hoe to plot a graph between number of cycles of load versus settlement of shallow surface footing resting on sand using OpenSEES?

07 August 2017 2,245 2 View

How to apply pulse load on shallow foundation using OpenSees?

A shallow foundation is modeled.Beams on Non linear Winkler Foundation (BNWF) model is used. after application of gravity load the pulse load is applied on the foundation as mentioned...

07 August 2017 1,314 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View