Analysis of CRD two factor using R studio ?

Hello everyone. I have conducted the research on post harvest longevity of tomato crop using plastic packaging and different doses of chemicals as two different factors. The design of experiment I...

28 February 2021 8,189 3 View

What is the role of work experience in motivating high tech entrepreneurship in Aviation industry?

Related work experience plays a vital role in motivating the Entrepreneurship. But when we talk about high tech entrepreneurship in Aviation industry, we talk about very high investment and high...

22 February 2021 376 5 View

Can we remove the fmoc group after peptide cleavage?

I have synthesized the peptide using Fmoc based solid phase peptide synthesis. Also I have cleaved the peptide from the resin and lyophilized it, but later realized that, I forgot to deprotect the...

21 February 2021 4,537 3 View

Why do we need to neutralize the charge of the system by adding ions before we proceed to energy minimization step in GROMACS ?

I am learning MD simulations using GROMACS and while I was doing a protein in water MD simulation a doubt raised. I was following the steps mentioned on the tutorials page and it said The system...

15 February 2021 5,514 4 View

How doping in nano-particles with same valency affect it's crystal lattice structure?

When doping in case of semiconductor is concerned, we doped Si by trivalent or pentavalent impurity atoms to improve its electronic properties but in case of nano-particles, sometimes we doped...

31 January 2021 7,128 1 View

How to prevent aggregation of nano-particles without using surfactants?

As it is well known fact that nano-particles can easily aggregate during nucleation/ synthesis part due to high surface energy..by reading literature, I came to know that surfactants can help to...

30 January 2021 8,206 6 View

How do I remove tetrabutylammonium perchlorate after electrolysis of organic molecules?

I am doing electrochemical oxidation of organic compounds for the the synthesis of nitrocompounds from simple organic molecules. I want remove supporting electrolyte after electrolysis. Please...

03 January 2021 7,858 2 View

Why the errors like the ones uploaded below happens while using Meta R/ Adel R?

Greetings everyone, I am learning to analyze multi-year and environment crop data using Meta R/ Adel R. But at some point during the process some errors were continuously observed and I could not...

18 December 2020 6,285 7 View

What is the best quality DNA for SSR fingerprinting?

Nanodrop result of my DNA samples extracted from fresh finger millet leaves showed 260/280 ratio ranged from 1.7-2.2 whereas 260/230 ratio ranged from 1.1-2.2. How can I assess the quality of such...

30 November 2020 8,689 6 View

Why Schiff bases change colour upon evaporation?

I got bright yellow coloured Schiff base after 6 hour reaction time. So i kept it for slow evaporation. Solvent was methanol. But after complete evaporation my product colour changes from yellow...

17 November 2020 3,824 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

Quantifying leaking DNA from bacteria - what's the secret?

Hi, all! I need to determine if my treatment causes membrane damage in bacteria (S. aureus and E. cloacae), but I cannot use a fluorescent probe such as PI and similar ones because my compound is...

24 February 2021 2,006 2 View