How quantify artifacts in EDA signal while using Biopac/Acqknowledge software?

Noëla Remond-Derbez @Noela_Remond-Derbez

21 September 2021 1 7K Report

Hello everyone,

Does Acqknowledge provide artifacts percentage in EDA signal ? Because we use filters/smoothing on EDA signal to reduce artifacts, but what about the remaining signal ? How take into account the difference of quality signal between our participants ?

Thank you for your expertise!

Noëla

Tilendra Choudhary

As per my knowledge, Acqknowledge does not provide the artifacts' level present in any signal. However, based on noises and artifacts which usually corrupt the particular signal, it suggests suitable filters with specific ranges to denoise the signal.

Badges
Science topic

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

How to calculate Total Flavonoid?

I analyzed flavonoid total spectrophotometry, the procedure as below: 2 ml supernatan added 5 ml dd.H2O, then added 0,15 ml NaNO2 5%, 5 minutes later added 0,15 ml AlCl3 10%, After 6 minutes,...

01 March 2021 6,722 1 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

RNA-seq DEGs downstream analysis and reporting in literature?

I used EdgeR to get the list of DEGs (differentially expressed genes) from my liver RNA-seq experiment. I have done the gene overrepresentation and GSEA based pathway analysis. I am currently...

23 February 2021 8,969 1 View

What are the ranges of four diffterent poles of butterworth filter for ECG signal?

Hi, Can anyone please tell me what are the ranges of four different pole orders such as first order, second order, third order and fourth order respectively of butterworth filter for ECG...

23 February 2021 2,554 3 View

Which polarizers are usually used to measure the birefringence of zebrafish muscles?

I already found several publications on that topic, however, the specifications for the used filters are often missing. Some more specific information than "fish is placed between to polarizing...

23 February 2021 1,934 1 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Is it possible, for a limited dateset of images, to use Convolution filters + Random Forest instead of UNet?

UNet is 'relatively' recent and was invented mainly to deal with biomedical images, yet is it also possible, for a limited dateset of images, to use Convolution filters + Random Forest instead of...

21 February 2021 4,858 3 View

The type of filter paper used to filter an epoxidized oil (the mixture is an epoxidized oil with magnesium sulfate) ?

I have a mixture of epoxidized oil and magnesium sulfate wich type of filtre paper should i use

21 February 2021 3,944 3 View

Algorithms to filter corrective max and min from a set of data?

I've got this 5 year Direct Normal Irradiance data I downloaded from https://re.jrc.ec.europa.eu/. I ordered this by year and by every 24 hours because I need the DNI curve by max in summer, min...

17 February 2021 2,777 5 View