How propagation delay can be added in Cooja?

06 June 2016 1 9K Report

I have 2 static motes at some distance from each other and one mobile mote for delivery of packets between these motes. I want to add some delay after receiving the packet from sink, so that it can be delivered to source node. I am unable to understand that how this delay can be added. I am using Cooja Simulator.

Help needed in this regard.

Vishal Rathod

Hello,

As per my knowledge, propagation delay does not support in cooja. Instead of that you can do some changes in radio mediums or interfaces. You can also create new medium and add to cooja that support propagation delay.

Badges
Science topic

More Babar Shahzaad's questions See All

Is it possible to change Affiliation in the paper before final publication in IEEE Journal?

My research article has been online on IEEE website for early citation and will be published in upcoming volume. I want to change my affiliation in that paper. Is it possible to change affiliation?

31 December 2017 5,769 4 View

How broadcast mode can be converted into unicast or multicast mode in Contiki CCNx protocol?

I am using CCNx Protocol implemented in Contiki OS. Details of this implementation are available in the given link. And source code for this protocol is also given in attachment. In this protocol,...

05 June 2016 5,076 3 View

How can the performance metrics in Cooja be evaluated in CCNx protocol in Internet of Things?

How can we calculate the metrics like interests generated, sent, satisfied, bytes sent, received etc. in Cooja Simulator like given table in attached figure taken from the document whose link is...

03 April 2016 3,765 2 View

How can I use Sensor Data Collect using Collect View in Cooja?

I am trying to run example code available for CCNx Protocol Implementation for Contiki OS and trying to observe sensors data in collect view in Cooja simulator. But it is showing no results in...

11 December 2015 4,821 6 View

How can Named Data Networking (NDN) layer be integrated for simulation in Cooja Simulator based on Contiki OS?

I want to use Named Data Networking protocol of Information Centric Networking for implementation of Internet of Things. So that the nodes can be accessed based on Names instead of IP.

10 November 2015 2,462 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View

Must a control group to be in the same semester that a experimental group for a study in education?

Hi everyone, I'm researching about mobile learning in higher education. Due to the small number of the students in the semesters, I cannot have a experimental and control group together. I'm...

22 February 2021 3,653 11 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View