How can Named Data Networking (NDN) layer be integrated for simulation in Cooja Simulator based on Contiki OS?

More Babar Shahzaad's questions See All

Is it possible to change Affiliation in the paper before final publication in IEEE Journal?

My research article has been online on IEEE website for early citation and will be published in upcoming volume. I want to change my affiliation in that paper. Is it possible to change affiliation?

31 December 2017 5,769 4 View

How broadcast mode can be converted into unicast or multicast mode in Contiki CCNx protocol?

I am using CCNx Protocol implemented in Contiki OS. Details of this implementation are available in the given link. And source code for this protocol is also given in attachment. In this protocol,...

05 June 2016 5,076 3 View

How propagation delay can be added in Cooja?

I have 2 static motes at some distance from each other and one mobile mote for delivery of packets between these motes. I want to add some delay after receiving the packet from sink, so that it...

05 June 2016 8,955 1 View

How can the performance metrics in Cooja be evaluated in CCNx protocol in Internet of Things?

How can we calculate the metrics like interests generated, sent, satisfied, bytes sent, received etc. in Cooja Simulator like given table in attached figure taken from the document whose link is...

03 April 2016 3,765 2 View

How can I use Sensor Data Collect using Collect View in Cooja?

I am trying to run example code available for CCNx Protocol Implementation for Contiki OS and trying to observe sensors data in collect view in Cooja simulator. But it is showing no results in...

11 December 2015 4,821 6 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How vulnerable is water and wastewater infrastructure to cyber terrorism in an age of IoT?

Im looking for any papers, reports,articles, links etc on information on How vulnerable is water and wastewater infrastructure to cyber terrorism in an age of IoT.

24 February 2021 2,750 4 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View

I am looking for a IoT simulator ?

I am working on a university project so, I m looking for a good Simulator compatible with LoRa and LoRaWAN protocol to simulate an IoT scenario. Thanks in Advance

20 February 2021 6,352 6 View

Truong-xuan Do

Check the link .

https://www.sics.se/msc-project-adapting-information-centric-networking-to-small-sensor-nodes

Babar Shahzaad

Thanks Truong-Xuan for your answer.

But this link doesn't provide me any mechanism about integration of CCNX protocol into Contiki OS which can be used in Cooja Simulator.

Is there any tutorial which helps about integration of CCNX in Conitki OS?

http://www.ccn-lite.net

Go to this link you can see source code, tutorial and publication related to your requirement. I couldnt give you more specific answers.

BR,