How post-hoc test should I perform for two way repeated measures ANOVA for 3 groups?

More Erbil Murat Aydın's questions See All

How much amount of DNA (ligation mix) should I use for transformation?

Hi Fellow Scientists! I am trying to clone my 300 bp insert into a 6 kb vector. I run a few different ligation reactions using (1:3 vector: insert molar ratios) 10, 20,30, and 40 ng/ul vector...

15 February 2021 9,563 6 View

How do We Maintain Appropriate Cell microenvironment with 3D Cell Culture Method?

3D Cell Culture is newly optimized and promising discovery in cell organization research and other researches that needs evindences in cell culture (in vitro) level. Are 3D Cell Cultures mimic...

23 September 2020 7,109 4 View

How do We Clarify the Effects of Drugs on DNA Replication?

DNA Replication and its components are common targets in discovering new drugs as antimicrobial therapeutic agents especially while dealing with antibiotic-resistant species and other diseases...

21 September 2020 6,172 4 View

Can you give information about how to calculate the molarity of MEA?

Hi, I am trying to produce CZTS films by sol-gel spin technique. Can you give information about how to calculate the molarity of MEA? Did you calculate the MEA molarity separately for each metal...

11 July 2020 3,415 1 View

Do weak contribution equations within a module use the module's boundary condition in COMSOL?

I am trying to solve a partial wave equation for scattered quasi-TE waves. I found the COMSOL built-in Helmholtz equation module very close to my problem. The bottleneck was that, I couldn't...

03 June 2020 8,937 1 View

How Can I find a reverse primer with good rating, if I need to amplify entire gene?

I need to amplify the KCNA1 gene. I could not design the reverse primer with GC content ~50%, G/C content between 40-60%, rating 100, and no secondary structure. Any help much appreciated!

25 May 2020 7,276 9 View

Is it possible to have more elements than nodes in mesh analysis of ansys?

During Centrifugal Pump Simulation by using ANSYS, I obtained more elements than nodes. Is this possible or the number of nodes should always be greater than number of elements?

04 May 2020 4,700 11 View

How should I compare pre test and post test of three groups?

Hi everyone, I have 2 treatment groups and 1 control group. I measured some physical parameters as a pre-test and post-test. Should I compare 3 groups pre-test and post-test separately by using...

23 March 2020 8,599 8 View

Plasmonics as a collective oscillation of holes instead of electrons?

In metals, the outermost conduction electrons (electron plasma) interact with incident photons and according to the classical Drude model, they may resonate and build up longitudinal plasmonic...

17 January 2020 1,559 7 View

How can I found Evapotranspiration lysimeter data for my research?

i need Evapotranspiration data around the world.

17 September 2019 3,887 5 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

How to manually calculate p value in ANOVA? what is the equation or formula for it?

03 March 2021 4,928 5 View

Mixed ANOVA - help?

I'm currently working on a piece which asks to conduct an ANOVA - looking at the effect of sporting group (2 levels), and exercise trials (two trials with six levels). I've computed this all...

27 February 2021 9,626 4 View

How to Interpret Partial Eta Squared Numbers For a Repeated Measures Anova?

I have obtained Partial Eta Squared Numbers through Two-Way Mixed Anova Analysis. My results for different constructs are: .105, .135, .038, .068, .061 respectively. I wanted to know, whether...

24 February 2021 7,122 1 View

Can we proceed to perform Two-way Mixed-ANOVA despite normality violations?

While testing assumptions, Shapiro-Wilk Test failed. However, I proceeded with the analysis and the interaction effect was significant. During our course- lectures, it was mentioned that Anova...

24 February 2021 228 3 View

Sample size determination for non-parametric tests?

How do I run a a priori sample size determination for non-parametric tests, like the Mann-Whitney U-test and the Kruskall-Wallis or other non-parametric tests that accord with the unpaired t-test...

24 February 2021 166 6 View

Three-way robust ANOVA in R?

I am trying to conduct a three-way robust ANOVA in R using the WRS2 package as: t3way(Stem ~ Species*Temperature*Salinity, data = tutto) and there is an error saying : Error in if...

22 February 2021 1,674 8 View

How to run repeated measures in mvabund?

I have a dataset of fish species abundances collected from 6 different habitats over the course of 30 years. Fish were collected multiple times per year and environmental variables were recorded...

21 February 2021 3,838 1 View

Which test should I use in SPSS if I have two independent variables and one dependent variable that is measured using two tests?

I am researching the effect of gender and video game use on reaction times. To do this, I will have participants complete two reaction time tests (a simple test and a four choice test). I am a...

17 February 2021 9,343 4 View

Béatrice Marianne Ewalds-Kvist

If you have a significant main effect or interaction effect in the overall (omnibus= analysis then SPSS give you automatically post-hoc test answers. It is likely to be Tukey' HSD test you get (HSD= honestly significant difference)

David Eugene Booth

You might look at the attached for some assistance. Best, David Booth

Jos Feys

See the " two-way repeated measures ANOVA" section (with R): https://www.datanovia.com/en/lessons/repeated-measures-anova-in-r/ or the "Two Factor Design with Repeated Measures on One Factor" section: http://www.personal.psu.edu/mar36/stat_461/repeated_measures/repeated_measures.html In attachment a SAS program, with the Tukey tests.