Level 1 pre-post multilevel regression: Panel data or ANOVA approach?

Dear colleagues, I am currently teaching myself in multilevel analysis using educational data. I found few to zero literature on basic analysis methods. In my context we frequently use level-1...

17 February 2021 9,378 5 View

Reliable and Valid Instrument for Causes of Medical Errors?

Is there any questionnaire/survey that measures the causes of medical errors? Example: physician negligence vs. systemic issues. Looking for a reliable and validated instrument. Thank you!

15 February 2021 2,874 4 View

Should the AUC in a concentration-time graph of a subcutaneous implant be roughly the same for poeple?

I have 2 concentration time curves of a subcut drug implant. the first group has a peak around the 50 day mark where as the second group does not. Both groups received the same implant by the same...

10 February 2021 2,305 3 View

Software for flow cytometry-like gating of data sets?

I am currently trying to do image based cytometry from fluorescence microscopy images. From the images I extract data such as cell size and a number of fluorescence intensities. Is there any...

09 February 2021 6,278 1 View

Can A. thaliana splice algae genes?

24 January 2021 329 2 View

Does long term preservation (10years) of Collembola in 99% Ethanol affect recovery rate of extraction by flotation?

Hello! I am currently developing an automated counting approach using Fiji to count Collembola from pitfall trapped samples that have been stored in Ethanol (99%) since 2010. I use flotation (tap...

13 January 2021 659 2 View

Co-stain Lectin PNA FITC conjugate with an uncojugated primary antibody?

Hello, I am planning to stain retinal tissue sections for IHC and want to co-stain cones and rods. For this we plan on using a Lectin PNA From Arachis hypogaea (peanut), FITC Conjugate for cones...

12 January 2021 583 1 View

How to use Abaqus USDFLD subroutine to vary stiffness?

Hi I have a problem where I am trying to vary the stiffness spatially across a structured interface. The whole idea is to vary the stiffness vertically, with a bulk stiffness of 8GPa decreasing...

06 January 2021 262 3 View

I really need help with cov-2 pseudotyped lentivirus production. Support?

Hi, i'm desesperate. i'm trying to produce lentivirus usinf BEI resources kit NR-52948. 24 hours after transfection i detect a massive GFP expression in my 293T cells. After 72 hours i filtered...

30 December 2020 9,889 6 View

How can i estimate the total phenolic content from a plant extract?

Suggestions and recommendations are welcome. A protocol used and experience would also be helpful.

25 December 2020 9,807 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)*S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)*S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View