How much is the Richardson number range in a estuarine system?

02 September 2015 1 4K Report

I work on a numerical model for investigating the structure of density and salinity in tidal estuarine system..How much is the Richardson number range in a estuarine system?

A. R. Karbassi

Dear Heron

It is very difficult to provide a range. It all depends on many factors such as salinity, depth, height of tides etc... as you know about them. A very broad figure may vary from 0.01 to 10. The attached paper may help you in many ways.

Badges
Science topic

More Heron Surbakti's questions See All

Best liquid trapping fluid for PFAS and related compounds?

I am looking for the best liquid adsorbent to bubble vapors through - the goal is to transfer the PFAS, precursors and other organics into the fluid while bubbling vapor/air through it. The fluid...

31 March 2021 1,569 2 View

How to conduct the cognitive analytical without machine learning?

Data mining technique has been used in the cognitive analysis in the purpose of predictions for business intelligence (BI). How the cognitive works without machine learning? What tool that makes...

14 September 2016 2,041 9 View

Is there any just-noticeable (JND) differences in frequency fro complex sound?

In complex sound I need to determine the fundamental frequency but the Fast Fourier Transform catch other frequency which have a small differences value with other frequency. Can anybody help me?...

03 June 2015 8,696 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal?

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice

04 August 2024 7,367 3 View