How is TMCP different from upset butt or flash butt welding?

05 January 2018 1 9K Report

How is TMCP different from upset butt or flash butt welding? Since in both flash and upset butt welding the material undergoes deformation.

Norbert Enzinger

upset butt or flash butt welding are welding procedures, while TMCP is a production route in steel manufacturing - I guess I do not understand your question properly.

However, if you refere to TMW this is a continous arc welding procedure with subsequent mechanical treatment of the solidified weld pool during cooling to mimic TMCP.

regards,

Norbert

Badges
Science topic

More Nikhil Shajan's questions See All

How can I connect two nodes using hinge connector (CONN3D2 elements) in Abaqus?

As shown in the attached picture, I am trying to connect two adjacent panels using Hinge connectors (CONN3D2 elements) with zero width and constant torsional stiffness. I wish to connect the...

06 February 2024 423 1 View

In the case of Metal-air battery (DFT approch), how can I find Entropy and Zero point energy?

Equation of Gibbs free energy G=∆E-ZPE-T∆S How finds the entropy and ZPE

08 January 2024 9,593 0 View

What method or data analysis technique can be employed to substantiate the impact of multimodal composing on enhancing the writing skills of students?

How can we demonstrate the efficacy of multimodal composing in enhancing writing skills, particularly in the context of academic writing, given the prevalent skepticism surrounding its...

07 December 2023 9,409 1 View

Can anyone tell me the difference between quantile regression and quantile on quantile regression?

when can it be used in corporate finance research?

27 November 2023 2,906 1 View

Quinolinic acid standard curve show reverse linearity when mixed with Blank serum samples?

When i use quinolinic acid in inreasing concentrations along with blank serum, the standard curve is surpisingly negatively linear! Expected linearity is reverse for this. However other standards...

18 October 2023 5,659 0 View

1 mg/ ml stock solution of kynurenic acid turn turbid when methanol is added?

When i make a stock solution of d5- kynurenic aicid (1 mg/ml), the solution is turbid and not clear. Inspite of sonication in water bath with mild heating, the suspension is not clear. Can i...

18 October 2023 9,790 0 View

Hii, Anybody has cif file for Na4VMn(PO4)3 material?

CIF file for rietveld refinement of Na4VMn(PO4)3 XRD data, using GSAS software if you have it, please provide me. Thank you in advance.

08 October 2023 7,038 3 View

How to plot RMSD from ab initio molecular dynamics simulations (AIMD) ?

I have performed ab initio molecular dynamics simulations (AIMD) using Gaussian program. How to plot RMSD ( Root Mean Square Deviation) plot from MD.out file?

19 September 2023 5,962 0 View

How to update parameters of Bayesian neural network?

I am trying to update parameters of Bayesian neural network using HMC algorithm. However I am getting the error shown below: ValueError: Encountered `None` gradient. fn_arg_list: [] grads: [None]

19 July 2023 5,686 1 View

What is the incident radiation used in XPS and why? How does the detector used in the XPS differ from those during SEM, EDX or XRD data collection?

23 May 2023 3,642 3 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Can an average household DIY spot welder be used for pouch cell electrode tab?

Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?

10 July 2024 8,763 0 View

How to calculate corrosion rate from potentiodynamic polarization test data for dissimilar welds?

we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...

30 June 2024 5,943 2 View

I am modelling resistance spot welding (2d) in comsol, so how to get nugget formation ?

I am using apparent heat method for simulation

14 June 2024 4,670 1 View

Analysis of Tensile Test Results Without Using an Extensometer?

I conducted a tensile test to analyze the strength of a welded joint and to implement an FEM model. Due to the high hardness of the base material, slippage between the grip and the base material...

10 June 2024 5,736 6 View

Batching process about FE-safe software?

I want to realize a auto-analyze process for weld fatigue by fe-safe software. However, I found that the current.macro in Tools can not record the commands of the GUI operation about defining the...

04 June 2024 5,089 1 View

How to model a groove weld location in Abaqus in a spiral pattern from the bottom to the top of the steel conical roof?

Hello, I have modeled a steel conical roof in Abaqus. Now I want to model the location of a groove weld in Abaqus in a spiral pattern from the bottom to the top of the roof. How should I model...

04 June 2024 9,833 1 View

How to define welded connection in Abaqus ?

I am trying to simulate the above truss in Abaqus to get its natural frequencies through Modal Analysis. The joints are connected through welding. However, I am unsure how to define the...

04 June 2024 4,071 1 View

I need articles about the difference between the application of kinetic and static friction coefficients in FSW welding, Can introduce the article?

In FSW welding simulation in Abaqus, I need some articles to check the difference between friction application methods (penalty - kinetic friction and static friction).

24 May 2024 5,006 1 View

Where to find Johnson-Cook parameters for pure Zinc?

I am currently simulating the impact of a zinc interlayer between Aluminum workpieces in ABAQUS (Friction stir welding process). While it was easy to find in literature the Johnson-Cook...

21 May 2024 1,643 0 View