How does transport of carriers occure in case photoactive quantum dots were blended within the dielectric layer in an OFET?

More Sara Bazhair's questions See All

What is the best way to measure the conductivity of a surface coated with metal alloy ?

Dear All, I have coated a piece of metal with an alloy of very thin thickness, how can I measure the conductivity? and what are the best devices to use for this purpose? Regards, Sara

06 July 2019 7,964 4 View

What is the definition of photosensitivity of a light detector? and why is it important to know the rise and fall time (photo-response)?

Dear All, What does photo-sensitivity tell us about the light detector in general? and is rise and fall time among the important figures of merit? and is photosensitivity of the phototransistor...

03 April 2018 6,219 2 View

Does mixing two materials, each of which is a solution of a different solvent, prevent their complete solubility together?

Dear All, As the question states, I have two materials, each is soluted in a different solvent. If I am to mix these two materials to form a single solution, should I consider using the same...

02 March 2018 7,612 3 View

What is the best method to clean a Si-SiO2 substrates with gold contacts without damaging it for depositition of an organic material?

Dear All, I have a Si/SiO2 substrate with pre-deposited Gold contacts, and i wish to clean it before I start depositing my organic layers for my OFET fabrication. Any Idea on the best method to...

01 February 2018 2,385 3 View

Why in some OFET structures the electrodes are multilayers of either cr/Au or platinum/Au?

Dear all, i understand that some papers use multilayers for electrodes to enhance the contact resistivity, but is this the only reason? and how does one decide the suitable material and...

09 October 2017 8,513 1 View

How to perform ligand exchange of quantum dots without damaging my OFET device operation?

Dear All, I am fabricating an OFET based on quantum dots/organic SC hybrid, my first attempet failed when I tried to do a layer by layer solid ligand exchange to the quantum dot active layer (I...

07 August 2017 1,595 13 View

is it possible to measure the nanosecond photoresponse (rise and fall time) of a phototransistor using an oscilloscope?

I am searching for common methods used with organic devices as well as cost effective methods and equipment. meanwhile i have an oscilloscope, but i am trying to find out how i should connect it...

06 July 2017 7,526 6 View

For Organic FETs: What is the difference between threshold and sub-threshold voltages? Why is on current/off current ration important?

Dear Respected Researchers, For high performance FET devices, specifically for Organic FETs, we require high charge mobility, in addition to low threshold voltage and high on-current/off-current...

01 February 2017 4,612 3 View

What is the most recent Infrared imaging technology currently applied?

Dear colleagues and Seniors, As the question is stating, I am searching for information and publications that describe the currently used technologies in Infrared Imaging Systems. With the...

01 January 1970 4,471 0 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What is Nano technology with coronavirus helpe the human..and is it nano mterals removal of covid19?

I anwar by adsorption or reaction ..but it is either more method...

02 March 2021 4,811 2 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Zno nano particles colour changed from white to grey in process of calcination any suggestions?

In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...

26 February 2021 2,435 4 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

S. Jaziri

Your sample is organic ?

Sara Bazhair

yes it is organic

Dear Faisal Al Mozahid and Abdullah Hasan Jabbar ,

the paper you recommended speaks of introducing a layer of quantum dots between the semiconductor and the dielectric.

since i also aim to study the device with light exposure, I'm searching for the effect of introducing photoactive quantum dots inside the bulk dielectric of the gate in an OFET(by mixing the QD in the dielectric material prio or during deposition).