How do we fitting of PSD data for AFM images?

07 July 2017 0 2K Report

When I have plotted PSD data and fitted with maybe Gaussian function, how do I relate the coefficients to the morphology of the samples?

Badges
Science topic

More Fredrick Madaraka Mwema's questions See All

ANSYS Explicit loads?

Hi I would like to apply loads in two steps in explicit dynamics as follows; 1. Apply vertical load without horizontal sliding 2. Then, with this load, apply an horizontal displacement Thank you

09 October 2017 6,698 2 View

Explicit

In Explicit Dynamics of ANSYS, how can I apply a distance varying load and velocity?

05 June 2017 4,592 3 View

When undertaking AFM roughness, is there any model for sampling to determine the number of points and measurements to take?

I am characterizing thin films

03 April 2017 4,641 1 View

Al films on metallic substrates, Can somebody share a paper on pure Al coatings on Stainless steel?

I am researching on pure Al films. Can somebody share a paper on pure Al coatings on Stainless steel?

02 March 2017 5,492 2 View

Are you asking Book chapter proposals?

Are you writing books? Are you calling for chapter proposals?

01 January 1970 5,879 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

My frequency output shows no errors, however, there's no frequency as a result on gausview. Does anyone know what I'm doing wrong?

I'm trying to perform a frequency calculation using Gaussian via MOBAXterm. The output shows no errors, however, there's no frequency as a result on gausview. The option "vibrations" is not...

31 July 2024 631 4 View

In SEM, if a latent variable consists of three observed variables, and each observed variable has four items, what should I do?

Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...

31 July 2024 3,913 6 View

Please guide me how to prepare samples for zeiss confocal microscope?

i am working on ischemic stroke. for immunoflourescence i want to use zeiss confocal microscope.before i used VS120 but the images from vs120 not so good now i want to use zeiss confocal but i...

30 July 2024 2,349 1 View

I have synthesized a composite of ZnO and In2O3 with variations in ZnO content. In Raman , what is the peak observed at 130 cm-1?

Dear all, I have noticed, as the ZnO content increases, the Raman intensity at 100cm-1 also increases. However, there is a peak nearby at 130 cm-1, which I could not find in any paper related to...

28 July 2024 5,410 1 View