How do I perform multiobjective optimization on energy systems (specially refrigeration systems) using genetic algorithms and MATLAB?

More Shitab Ishmam's questions See All

Why do we find fluctuations or spike in SASA diagram?

Recently I have done SASA ( Solvent Accessible Surface Area) analysis for one of my research. But I have found some high fluctuations in SASA diagram which are actually 5 times higher than the...

21 July 2023 1,203 3 View

Can I download Yasara for free?

I am trying MD simulation for some of my compounds using NAMD. But not getting satisfactory result. I think I should use Yasara. But I can't afford It's licence. Can I download it for free?

06 March 2023 7,367 6 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How to develop investments in renewable energy sources?

08 August 2024 5,112 3 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

Is there a database with onshore wind production for the wind farms in Portugal?

I am looking to predict some production for future onshore wind energy production in Portugal, is there any database with info of performances of the existing wind farms in the country? something...

28 July 2024 1,750 1 View

HAs anyone used TGA to find activation enegy of water evaporation?

I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....

28 July 2024 9,545 6 View

Azu Azaath

you can use gamultiobj in pso toolbox it is easier & very useful to solve your problem

Soheila Ghambari

Dear Shitab Ishmam,

This link can be helpful:

Best Regards...

http://yarpiz.com/56/ypea120-nsga2

Jörg Bremer

Hi,

maybe this paper

https://www.researchgate.net/publication/262455215_Multi-objective_optimization_of_household_refrigerator_with_novel_heat-storage_condensers_by_Genetic_algorithm

might be of interest to you

Article Multi-objective optimization of household refrigerator with ...