How do I model shear force in Abaqus?

09 April 2021 1 4K Report

I am modelling cell detachment in abaqus, using the cohesive zone approach. I dont seem to know what load category I can choose and how can I apply the load to mimic the lift and drag force required to cause deformation or detachment of the cell...can someone please help me

Ibrahim Al-Najati

I think this video can be helpful..

https://www.youtube.com/watch?v=O15fWvU-_BA

Badges
Science topic

Similar topics
Engineering
Modeling

More Killian Onwudiwe's questions See All

Discontinuity between each step, ANSYS LS-Dyna Restart?

Hi all, I'm working on a 2D model where I impose a force to the lower part, and then I want to impose a horizontal tiny displacement on the same part. So I chosen to decompose this model into 3...

04 February 2024 881 0 View

Discrepancy in the general consensus of measuring phycocyanin spectrophotometrically: OD615 or OD620?

I am testing various methods of extracting C-Phycocyanin from fresh Arthrospira platensis biomass. To quantify the phycocyanin concentration within my solvents after extraction, I use the...

29 December 2023 5,612 0 View

Warning : "There are 2 unconnected regions in the model." in ABAQUS ?

Hi all, I'm working on a 2D model where I impose a little vertical displacement to the half-sphere into the parallelepiped. I declared a node-to-surface contact with these properties : Normal...

10 December 2023 3,182 3 View

What is the best way of analyzing DOE data with zero inflated dependent variable? Is it ok to use the zero inflated models ie ZIP, ZAP, ZINB etc.?

We are working with experimental data in which the dependent variable of interest (is count) has a lot of zeros and some few 1's across the treatments under investigation. we therefore need...

09 September 2021 10,057 1 View

Digestibility of nutrients in commercial fish feeds?

Dear all, I am looking for nutrient digestibility coefficients (ADCs) for commercial feed used in several fish aquaculture species (D. labrax, S. aurata, A. regius, S. salar, S. trutta, O....

02 June 2020 5,159 3 View

What are the recommended Emotional Intelligence scales that are 1) validated and 2) free?

I am designing a program evaluation of a social work study abroad class and seeking an Emotional Intelligence scale to use with undergraduate and graduate students who will be engaging in...

03 May 2017 7,365 5 View

Can anyone tell me his/her experiences with "older" cDNA obtained from microRNA? What about the (long-term) stability?

I found two controversial papers about the stability and would be glad to hear any comments on that issue. Thanks!

21 August 2013 6,602 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View