hello guys
My question is "how to determine lattice parameter of a tetragonal system by using Nelson -Riley equation"....?
Hello everyone, I have synthesized NiMnSn alloy by ball milling technique. XRD study indicates that the system shows orthorhombic crystal structure. I have calculated...
07 August 2017 472 7 View
Hello everyone, I got a MT curve (magnetization vs temperature) (Temperature range: 5K to 300K and 5000 Oe magnetic field) of NiMnSn alloy synthesized by arc melting. What does it indicates?...
06 July 2017 8,831 3 View
Dear Researchers, I have prepared some alloy samples (NiCuMnSn) by ball milling. The obtained powder was converted into 10mm pellets and then heat treated at 950 degree celcius (under very high...
08 September 2016 4,941 1 View
Hello Researchers, I have Nickel, Manganese and Tin powder (particle size is less than 100 micrometer for all). I want to make single phase alloy by arc melting technique. Oxides are not desired....
04 May 2016 7,393 5 View
Dear friends, I want to sinter a pellet of NiMnSn alloy in vacuum furnace at 900 degree centigrade temperature under high vacuum for 8 hours. Since we do not have vacuum...
01 February 2016 2,186 5 View
I am working with magnetic Heuslar alloys. Kindly explain how to test a material's magnetic shape memory effect. Which equipment is required for this purpose?
31 December 2015 6,424 2 View
shape memory material
04 May 2015 4,972 6 View
What does following terms mean? Kindly explain for the powder and thin films in both context. Particle size Crystallite size Grain size How these terms are correlated with each other while...
03 April 2015 3,645 0 View
I have an alloy sample and the selected area diffraction pattern of this alloy is showing polycrystalline rings. How do I calculate planes from those rings?
02 March 2015 1,120 5 View
Please write the steps of Rietveld refinement in Fullprof software.
02 March 2015 7,173 2 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...
31 July 2024 3,913 6 View
Can a researcher use small sample size of 40 while using SEM with bootstrapping of 1000 and is it possible to get published
28 July 2024 4,402 2 View
Does it exist some special technique for cutting ceramic membranes for Cross-sectional FESEM or SEM images?
25 July 2024 5,482 2 View
I have an issue with SEM imaging of liposomes. When measured by DLS, they appear to be around 120 nm, but when using SEM with simple air drying, they appear much larger, around one micrometer.
25 July 2024 3,395 3 View
I have designed magnetic material with different biasing conditions in HFSS. Now I want to give an RF AC signal and do a transient simulation in HFSS. Is it possible to do in HFSS? Please help me...
24 July 2024 9,319 5 View
Hi everyone, I have conducted a mediation analysis with SEM. My model fit was good but there was no significant mediation. Which aspects of this should I discuss?
19 July 2024 4,272 5 View
I'm evaluating the reproductive performance of quails. I have the fertility, and hatchability percentages for six different sire groups and would like to determine the significant difference...
14 July 2024 2,203 5 View