How do I calculate the refractive index of mild steel material by remote source?

More Pranav Shinde's questions See All

What is the effect of low temperature performance between low carbon and high carbon steels?

AISI 1035 vs AISI 1045 peeformance?

31 December 2017 6,363 3 View

Why is stress-strain curve of austenitic stainless steel different from carbon steels?

Please see linked image

01 February 2017 4,991 0 View

Find residual stresses through XRD in formed tube?

I have a formed tube with reduction in diameter, i need to find residual stress through XRD. For sampling I can either cut a small section of hollow tube or make powder of it. If i turn my sample...

09 October 2016 735 8 View

How does the mechanical properties vary from extruded aluminium tube to pressure die casted aluminium tube?

Considering application for torsion only.

08 September 2016 2,308 9 View

In Ansys fatigue calculations how do you provide frequency of one cycle?

How does the calculations take into consideration effect of time.

08 September 2016 8,091 2 View

How to calculate theoritically work hardening induced stresses due to tube forming process?

Is it possible to get values in LS Dyna?

08 September 2016 6,581 5 View

Can we establish a relation between von mises, prinicpal and shear stresses?

For FEA calculatons

08 September 2016 1,712 1 View

Does curl of a function neccesarily needs to be constant?

What does curl of function physically represent?

07 August 2016 5,423 3 View

Improving residual stresses in DMLS/SLM AM components?

Using techniques like laser shock peening and particle shot peening, residual stresses at the surface can be taken care of. But how is it possible to cure internal residual stresses within core of...

05 June 2016 651 1 View

How are residual stresses in material compared with Grain size?

Macro residual stresses are considered to be larger than the grain size, how is this justified and understood.

04 May 2016 6,504 14 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

How to increase citation in Research Gate?

How to enhanced h-index in Research Gate?

04 August 2024 3,368 4 View

Request a single Lecture notes for math as detailed as this that I can find in one place?

- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...

03 August 2024 2,366 0 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

Babu Bhaskaran

Refer this link:www.filmetrics.com/refractive-index-database

Refer this link:refractiveindex.info/

Refer this link:www.dtic.mil/dtic/tr/fulltext/u2/692714.pdf

Refer this link:www.dtic.mil/dtic/tr/fulltext/u2/704555.pdf

Christian Röling

Have you tried Spectroscopic Ellipsometry? Is the steel intrasnparent than you can convert the spectra directly into n+k values.

Best regards

Christian