How could I open end of the titanium oxide nanotubes?

More Hamideh Kashani's questions See All

What are the reasons of shifting peaks to higher and lower potential in anodic scan and cathodic scan , in CV?

Hi in Lithium ion battery, shift of peak to higher and lower potential in anodic and cathodic peak at the second cycle of CV is attributed to better kinetic of Li insertion and extraction into...

08 September 2016 6,438 5 View

What is the best conditions for formation Magnetite ore deposits?

I want to know more about Magnetite deposits.

06 August 2024 1,066 0 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

¿Are oxygen vacancies in semiconductors capable to change the band gap?

Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...

30 July 2024 8,339 2 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

What is the solubility of Iron (+3) in Bismuth Oxide?

Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco

29 July 2024 2,163 1 View

A twin-shaft kiln or a rotary kiln for lime production 1 class? if compressive strength of limestone is low 60 MPa?

My research work is related to the calcination of limestone. I have a complex question and would like to consult with experts in this field. Could you please advise which kiln to choose (a...

18 July 2024 1,390 2 View

Could Nd doping into TiO2(anatse) because Nd's dense diameters are bigger than in TiO2 ?

could Nd (Neodimyum) doping into TiO2 because Nd's dense diameters are bigger than in TiO2

11 July 2024 2,350 2 View

Determine pore diameter by BJH of TiO2?

Dear all, l need to help me to determine pore diameter. I got from BJH data the rp(peak area), Desorption Isotherm was 1.6 nm, but from Isotherm l got type lV with hysteresis H2 loop. Can l used...

10 July 2024 2,872 1 View

Valery Ray

You can try to use FIB to cut off the blocked end and see if the rest of the nanotube is hollow...

Hamideh Kashani

thanks to your answer if you have any paper about it may inform me because my work is very sensitive to pollution so I should know exact process

"Strong, Light, Multifunctional Fibers of Carbon Nanotubes with Ultrahigh Conductivity" Science 11 January 2013: vol. 339 no. 6116 182-186 - See Fig. 3(E)