How could I improve the process of reconstitution of nanoparticles?

More Eloy Pena Rodríguez's questions See All

Which is the energy (J/cm^2) provided by a UV lamp (220V 50Hz) during 50 min of exposure at 5 cm distance of samples?

I am planning to do a phototoxicity experiment in which I need to apply an UV Energy lower than the highest non citotoxic energy. Based on literature it should be around 5J/cm^2 for my cell line...

04 May 2019 3,818 5 View

No title

I am doing an in vitro release study (dyalisis) of an active ingredient loaded in PLGA Nanoparticles. I want to get the standard deviation so, should I collect replicates of 500 uL for each time...

08 September 2017 8,262 3 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Can chitosan alone can act as a reducing agent for Cu(0) nanoparticle sythesis?

[Synthesizing Cu nanoparticles without using chemical reductants]

01 March 2021 8,359 1 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

How can I calculate the rdf of water molecules around 'Na' ions that are closest(adsorbed) to the nanoparticle(solute)?

Hi, I want to calculate the radial distribution function for water molecules around the Na+ ions adsorbed on the surface of a spherical nanoparticle using the gromacs trajectory dynamically? For...

28 February 2021 5,650 1 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Why there are two peaks while using the mie plot of Silver nanoparticle?

Hi, I am trying to learn the theoretical modelling of silver nanoparticle using the Mie scattering theory. After that, I discovered a software named Mieplot developed by Philip Laven, where it...

25 February 2021 7,493 6 View

Omar Gonzalez-Ortega

After drying it will be very difficult to redisperse. Are you sonicating the sample? Were the silica particles protected before drying?

Syed Salman Hashmi

Adjusting the pH and sonication followed by vortexing might help.

If sonication will favor the release of the drug then the system is not properly designed. Anyway any peg derived surfactant might help. Do not dry the sample if possible.