The fundamental technique to directly detect carrier density and interface states in semiconductors is capacitance measurements (C-V),35-37 which provides critical insights to elucidate the 2D-FET operation mechanism.
my question is how is that?.
Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?
03 March 2021 1,763 2 View
I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...
03 March 2021 2,297 3 View
03 March 2021 8,272 1 View
Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...
03 March 2021 2,037 3 View
Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...
03 March 2021 6,317 1 View
i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).
03 March 2021 7,100 1 View
03 March 2021 5,360 2 View
The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...
03 March 2021 4,107 4 View
If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis
02 March 2021 7,670 3 View
02 March 2021 5,204 3 View
Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...
01 March 2021 2,327 1 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
I have a model with bulk material (matrix) and inclusions and cohesive interface elements between both. For the bulk material, I have implemented a UMAT and for the cohesive interface elements, I...
20 February 2021 1,286 2 View
I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...
19 February 2021 2,787 1 View
I have done electrochemical impedance by using cyclic voltammetry for one organic material. from that, I plotted bode diagram. but actually, I am very confused about how to find the capacitive...
18 February 2021 3,023 3 View
I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...
16 February 2021 8,514 2 View
Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm from the exposed surface in Abaqus... i am performing a coupled...
10 February 2021 4,656 2 View
Hello everyone, I'm trying to mesh a structure with complex partitions using mesh controls. When doing it on the user interface I'm first selecting all cells. In the following, I have to accept...
03 February 2021 8,198 1 View
Hi everyone, I'm trying to simulate some graphene nanoribbons to determine their electron mobility. I use DFTB+ for simulation software. With this software I can plot transmission in regards of...
03 February 2021 9,315 3 View
I am trying to measure resistance from I-V curve from a chemiresistor/ FET sensor with a keithly sourcemeter. The substrate is soaked/ wet with protein and phosphate buffer only. But the I-V line...
24 January 2021 8,009 3 View