28 August 2022 1 6K Report

Dear researchers,

How can we warm a very high TDS water on the lab and pilot scale?

Thank you so much

Regardson

More Foroogh Khodadadi's questions See All
Is there any graph to determine the membrane pore size based on its BSA rejection percent?

Dear researchers, It is clear that BSA protein is the most common solute for membrane performance examination. However, there is no reference to check the MWCO of the membranes based on BSA...

29 April 2020 6,148 3 View

Can DMAc, NMP, DMF, TEP, DMSO, Formamide, Acetone, as organic solvents, dissolve a few drops of an oil?

Dear researchers, The mentioned solvents are organic solvents and it is thought that they can dissolve the oils. If they are not capable to do this, what is the reason? Regards DMAc:...

25 February 2020 140 2 View

EEG connectivity calculation via HERMES toolbox ?

Hello everyone I am currently trying to calculate phase lock value for my EEG data with the help of the HERMES toolbox in Matlab. I have a total of 48 subjects with different channel location...

04 January 2020 5,220 1 View

How can we calculate the amount of residual non-solvent (pore-former) additives in the membranes?

Dear researcher, We all use the non-solvent additives to improve the structure and performance of the polymeric membranes. However, the non-solvent additives can be easily washed out quickly with...

29 December 2019 5,366 1 View

What is the software that is used for adjusting and labeling the images for journal articles?

Dear researchers, I want to put my SEM photos together to have a picture like the attached photos for my article. Could you please guide me what is the software that I can use? Regards

16 December 2019 4,165 12 View

Which laboratories or institutes in Iran are able to determine estrogen hormone concentrations?

Dear researchers, I want to determine the estrogen hormone concentration in water. Where is the special laboratory to do this in Iran? Could you please guide me? Best regards

11 December 2019 2,829 2 View

What are these white bubbles on the surface of the SEM micrographs?

Dear researchers, There are some white bubbles on the surface of the SEM micrographs. What are these particles? Kind regards Foroogh

25 November 2019 5,365 3 View

How to make the brittle polymeric membranes more flexible and soft?

It is reported that PES/DMSO membranes are too brittle. Is there any method or additive to make them more flexible? Regards

18 October 2019 1,576 6 View

Can you introduce an accessible and inexpensive natural surfactant?

Dear researchers, The surfactants are extracted from the nature are more useful. Can any one introduce an available cheap (herbal) surfactant to produce water/oil emulsion? Thank you so much....

08 March 2019 4,539 7 View

Has anyone installed the Amira Avizo software?

Dear Researchers, I need a 3D photo of a porous material such as attached one only to show the porosity, not for analyzing porous materials. Can any one help me? Regards Foroogh

19 October 2018 7,403 6 View

Similar questions and discussions
What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

Why is the sum of the elements in a row in a Q matrix equal to zero?

When explaining substitution models, the substitutions are expressed as Q matrix. Why is the sum of the elements in a row zero?

28 February 2021 3,864 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close