I want to simulate welding process using ANSYS transient heat transfer analysis. Volumetric heat generation given to elements body load as HGEN in ANSYS. But, one single node is common for four elements, shall we divide the hgen value by four.
There is article here
http://aws.org/wj/supplement/03-2004-NGUYEN-s.pdf
It depends on where the heat generation will be applied to.
There are various commands to apply heat, i.e. BF, BFE, BFA, BFV...
In my opinion you can use BF, in which the hgen is applied directly on the nodes. Thus you don't have the problem above anymore.
I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.
29 July 2024 6,115 0 View
Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.
29 July 2024 4,538 3 View
I wanted to know whether we can observe the synergistic/antagonistic/additive properties of combinations or mixtures of compounds through docking analysis. But during docking preparation any...
28 July 2024 7,413 6 View
During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...
08 July 2024 1,330 0 View
HOW TO WRITE GREEN CONSUMER BEHAVIOUR AS A LITERATURE REVIEW
28 June 2024 2,661 0 View
I found atomic% and weight % of doping element decreased in the resulting compound on increasing its concentration.
28 May 2024 2,455 2 View
I need to find out the desired dose for my poly herbal formulation. Please guide me how to get the figures
12 May 2024 8,290 1 View
Dear All, I have an imagery with a single fish species within each image along with a list of morphometric measurements of the fish (length, width, length of tail, etc). I would like to train a...
28 April 2024 2,090 2 View
Is there any formula to calculate stress
20 April 2024 8,612 2 View
The pan-country study could have further divisions/categorization based on different criteria. Any recommendations would be greatly appreciated. Thank you!
27 March 2024 991 1 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...
09 August 2024 7,615 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...
06 August 2024 1,896 1 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...
04 August 2024 8,997 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View