How can we link, HS codes with NIC codes of manufacturing sector?

01 February 2018 0 4K Report

I need to link HS codes with NIC codes to get the products which are exported most and need to calculate some statistics using ASI dataset which has NIC codes.

So, does anyone know How can we link, HS codes with NIC codes?

Badges
Science topic

Similar topics
Books

More Saloni Khurana's questions See All

Is it possible for a manuscript to be rejected after undergoing review for 4-5 months? Journal status:review completed, pre-print status:under review?

how should one interpret these conflicting signals? Waiting for acceptance or rejection of a paper can be stressful, especially with such ambiguous indicators.

21 April 2024 10,030 8 View

Dear Researchers, I would like to have your suggestions regarding the solubility of Particulate Matter (UPM-SRM1648a) ?

I have tried dissolving the same in DMSO and water at 1mg/ml, sonicated the stocks but there was precipitate formation and l could not get a clear solution.

10 October 2023 7,567 0 View

Dear researchers, Can anyone please suggest upon the solubility of Imiquimod ?

I have tried dissolving the same at 1mg/ml in both water and DMSO but there was precipitate formation. I even tried heating and sonication but there was no effect as there were precipitates.

10 October 2023 2,121 1 View

How can I convert mass ion intensity (%) to ppm?

I am analyzing UPLC-MS data, where I don't have standards and performing a non-target screening of small-molecule compounds. How can I convert the mass ion intensity which is in percentage to ppm...

18 June 2023 2,164 2 View

What is the manual process for interpreting LC-MS data?

Which freely available databases/tools/web servers can analyse LC-MS data to identify compounds and metabolites based on their m/z ratio values?

31 May 2023 2,621 5 View

Trouble reaching low temperature in Oxford microstat N heating and cooling stage ?

We have an Oxford microstat N heating and cooling stage. Temperature does not reach below 230K also it starts increasing again and again. Please help with a solution.

25 December 2022 1,008 1 View

Can I use Plasmodb database to extract and analyze single cell RNA-seq data for Plasmodium?

Hello everyone, I am working on some set of genes of Plasmodium parasite and wanted to extract and analyze their gene expression data on wild type parasite and mutant ones. So I am designing the...

28 June 2022 5,024 0 View

What is the effect of riser height in sand casting, keeping the diameter same ? How the height of riser effect the weight of casting ?

Increasing the height of the riser in sand casting and keeping the diameter the same, results in decreased density and a decrease in casting weight. What is the phenomenon for this weight reduction?

25 April 2022 5,743 4 View

PCR conditions for fungi TEF alpha tricho primer?

For fungal identification I will be using TEF ALPHA tricho primer which has Tm 52°C. I wanted to know the PCR conditions as even by setting the annealing temperature at 48°C I was getting multiple...

21 February 2022 9,787 3 View

TEF ALPHA tricho primer PCR conditions for fungi identification?

I wanted to perform PCR for fungal identification using TEF ALPHA tricho-F and R primer with Tm 52 as given by the seller. But even after performing PCR at 48° and 56°C (annealing temp) I got...

20 February 2022 2,536 2 View

How to set the environment variable for incorporating the GD3 dispersion in G16 for performing calculations using the OPBE functional?

I have incorporated the dispersion effect for the OPBE functional by specifying the S6, SR6 and S8 parameters for GD3 in Gaussian G09 package. For this purpose, I have defined the environment...

05 August 2024 1,494 2 View

How to test multivariate outlier in STATA?

Hey all, I need help testing for multivariate outliers using STATA for my master thesis. The literature recommends the Minimum Covariance Determinant (MCD) (Verardi & Dehon, 2010). I found the...

22 July 2024 8,821 2 View

How to classify 3D Bioprinting as a part of Additive Manufacturing?

Hello, I have a problem in classification of "Additive Manufacturing" techniques. There are several classification for Additive Manufacturing e.g. Powder, Extrusion, Resin etc. Actually, I am OK...

15 July 2024 139 3 View

I need Agile topic for my PHD ? any recommendation ( Safe) ?

Hello All, it has been a while searching for a good topic to Agile, and also i need topic that can do a real impact in agile field? any recomendation ?

07 July 2024 8,450 3 View

What role does grain size play in the mechanical properties of nanocrystalline metals and how can this be controlled during the manufacturing process?

In nanocrystalline metals, the size of their crystalline grains affects how strong, ductile, and hard they are. Smaller grains often mean stronger metals but can reduce ductility. Controlling...

28 June 2024 6,925 0 View

How can I prepare the csv. dataset to find the flood triggaring factor using ANN?

here's a concise guide for preparing your CSV dataset in Excel to identify flood-triggering factors using an ANN: Clean and Format:Address missing values (fill with mean/median or remove if...

21 June 2024 7,941 0 View

Export of Opus map in matlab?

Hello everyone, i have hyperspectral dataset recorded on a hyperion (Bruker), in opus file (.#). I would like to send the data to matlab, but i am lost... I just managed to export one spectrum via...

20 June 2024 3,412 0 View

Why R-Square calculation show different value between STATA result and Eviews?

So my student have a question that i cannot answer as well. She analyzing the effect of ICT toward labor productivity using 8 years data panel using 4 independent variables with EVIEWS 13. Frankly...

12 June 2024 5,183 4 View

How to use superscript in the forest plot using Stata?

I am creating a forest plot for a meta-analysis and require assistance in adding a superscript after the Author/Year on the left side of the graph. Any help would be greatly appreciated.

09 June 2024 5,319 4 View

My MEGA 11 software closes on its own when I am running a phylogenetic analysis in the 1000 bootstrp?

I have ran the analysis a hundred times now. Still after like 200-300 replicates my software stops analysing or just closes on its own.

26 May 2024 6,125 4 View