An article on the Iranian state's civil liability in the COVID-19 matter needs supervision; Is anyone interested in collaborating?

Hello. An article on the Iranian state's civil liability in the COVID-19 issue has been written in collaboration with a friend and a comparative look at law and biology. The article is ready to be...

15 February 2021 2,906 2 View

Is it possible to report hydrodynamic loads on different parts of an ocean vehicle while 6DOF motion analysis in Ansys Fluent is running?

It seems a 6dof UDF containing vehicle characteristics such as mass and moments of inertia can be used for specifying a boundary as reprentative of ocean vehicle. It is required to have...

03 February 2021 7,726 3 View

How to determine the pH pzc (point of zero charge) for metal-organic frameworks and Organoclays?

I need to answer this question to continue my research.

12 January 2021 3,626 5 View

Is it possible to identify of ordered phase with x-ray diffraction technique?

I want to identify ordered phases in a high entropy alloy.

11 October 2020 5,452 4 View

How is solubility of CO2 or air in organic solvents such as xylene or cyclohexane?

For some reason, I need to inject a dispersion of an organic solvent and organoclay into a block of soil sample. the organic solvent probably is xylene.

29 September 2020 6,348 4 View

Should Quartz powder or Sand water absorption be considered for UHPC mix design calculations? How is the water absorption of the powder calculated?

07 August 2020 1,592 1 View

What is the real surface of the platinum electrode?

17 May 2020 5,493 5 View

What is the best solvent to dissolve nanoclay (montmorillonite)?

I need to inject nano-clay to some kind of collapsible soil (silty loess) to stabilize and strengthen it. I can't use water since this soil is moisture sensitive and water may dissolve the bonding...

26 March 2020 1,675 3 View

How I can eliminate 50Hz parasitic magnetic field and the at same time do not affect existed DC magnetic filed?

My application is EFNMR (Earth field nuclear magnetic resonance). In this application the earth filed, which is a DC field, has the main role and should not be altered. However, all other magnetic...

10 January 2020 337 2 View

Hi.please someone explain me how to fabricate semiconductor?

I want different new ways for this subject.

06 November 2019 7,957 2 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View