How can the welding of reinforcement effect the compression and tension capacity of concrete?

05 May 2014 1 3K Report

Welding in rcc

Yes on the material hardness increases or embrittlement can occur at the welding point. The heating and the cooling process should be well chosen.

Badges
Science topic

More H. M.A. Mahzuz's questions See All

How can i insert or introduce and analyze deformed rebar with concrete in RCC beams in ANSYS?

Can anyone tell please, how can i introduce and analyze deformed rebar in RCC beams in ANSYS? Please share any resource if you want.

01 February 2017 6,166 2 View

Theoretically is it possible to make time slower than that of earth ?

Theoretically is it possible to make time slower than that of earth? Since earth has a motion, our solar system has a motion, our galaxy has a motion....so on. So why not have a reference point...

11 December 2016 7,289 6 View

How to generate a multi variable non linear equation from a data?

Any software, online software or tools???? please mention

11 December 2016 1,900 3 View

Please share any example/ calculation of design of tall or super tall buildings?

Both concrete or seel

07 August 2016 3,567 5 View

Please share any resource or link to design tall buildings?

Both concrete or steel, having different structural systems.

05 June 2016 3,109 3 View

Theorically how is it possible to select the most economical combination of mix ratio for a concrete (e.g. 5000 Psi)?

Theorically how is it possible to select the most economical combination of mix ratio for a concrete (e.g. 5000 Psi)? Is there any procedure?

31 December 2015 5,352 5 View

What do you mean by "TOP JOURNALS" in research gate?

09 October 2015 9,441 0 View

What is the systemetic process of writting a PhD thesis (Engineering field)?

Regarding a systemetic process of writting a PhD thesis (Engineering field)

31 December 2014 6,352 4 View

What is opinion regarding this paper?

special concern: methodology and result

08 September 2014 8,893 2 View

How do you determine the capacity of an existing masonry wall?

Is there any NDT test/code or anything to do such work?

05 June 2014 2,525 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Some new emerging problems on application of RL for scheduling in IoT networks?

I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...

01 August 2024 8,754 2 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Best Practices for Constructing and Maintaining Gravel Roads in Rural Areas?

Hello, I'm involved in a project focused on constructing and maintaining gravel roads in rural areas. We're particularly interested in ensuring durability and reducing maintenance costs over time....

29 July 2024 9,623 0 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View