10 October 2017 1 2K Report

Which modeling procedures are there for such a problem? I need materials and videos on such modeling

More Collins Nana Andoh's questions See All
Can I get help from any of us who is SRIM code expert?

I have run some data and needs helping hands in discussing my results. 

06 July 2015 798 0 View

What are some of the effects of neutron-stainless steel interaction?

what can one say about the number of displacement, ionization energy, energy loss to phonon, sputtering yield.?

05 June 2015 6,861 0 View

Can someone help me with a LAMMPS input file and Interatomic Potential file to adapt in determining the bulk properties of some stainless steels?

I about to determine the bulk properties of 7 different types of stainless steel (grades 304, 308 and 309) that am determine its bulk modulus and all my efforts seems futile.  

03 April 2015 3,852 4 View

Which output best describes Damage assessment with SRIM-TRIM software?

I have done some SRIM-TRIM analysis on some metals. Please which of these outputs (Ionization, Sputtering, Vacancies, Range etc) is best describing the damage.

11 December 2014 7,472 5 View

Why do we employ LAMMPS in MD simulations and what does it do in terms of mechanical strength analysis?

Dear all, Can someone brief me on the use of LAMMPS in Molecular Dynamic simulations? Thank you

10 November 2014 5,128 2 View

Why can't I run my downloaded LAMMPS executable together with the MPI on windows?

Please guide me from the prompt. Since I am trying to run the Al99 tutorial and am getting problems with it. Thank you

10 November 2014 6,028 2 View

Similar questions and discussions
Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close