How can I study the transport characterization of a ionic liquid dopped polymer electrolyte?

24 March 2017 1 9K Report

Please help me to study the transport properties of ionic liquid doped polymer electrolyte

Dear Tihomir Nikolaev Tsanov

I am not clear about transport characterization. When I uploaded my paper to membrane science they told me to do it. I think it will be electric properties or ionic conductivity. Since it is ionic conducting in nature.

Badges
Science topic

Similar topics
Statistics
Survey

More Safna Hussan K.P's questions See All

Is the Difference Between Numerical and Experimental Results of 3D Printed Ribbed Plates in Abaqus Due to Tie Constraints?

I am developing a numerical model that optimizes the placement of ribs or stiffeners on a base rectangular plate. For the base plate, we use shell elements, while the ribs or stiffeners are...

12 February 2024 7,837 2 View

Covert vector into an image using matlab?

I am trying to convert vector into an image using the code below clear variables load(Exe4_2022.mat') n = length(b); figure, imagesc(reshape(b,sqrt(n),sqrt(n))), colormap(gray), axis off; But I am...

03 December 2022 8,086 5 View

Linear least squares problem??

linear least squares problem:: fit f(t) = sin(t) on the interval [0, π] with polynomials of degree n with n = 1, 2, 3, · · · , 10. Here, we use equally spaced nodes. Solve the normal...

30 October 2022 2,371 5 View

Comparison by applying the hydrostatic pressure on middle and Top of shell surface in Abaqus?

I have done a comparison by applying the hydrostatic pressure on the middle and top of the shell curve surface (Section Assignment: Shell offset = Middle or Top surface in Abaqus). In the case of...

17 August 2022 8,688 0 View

How do I set up Abaqus for topology optimization?

We usually use Strain Energy as an objective with volume constraint in topology tasks. But if I want to reduce the mass/volume reduction of structure as much as possible until displacement along...

16 December 2021 328 3 View

k....jjkkkk ty?

07 December 2021 2,226 2 View

I have dry leaf powder of mash plants , i want to analyzed by FTIR what types of metabolites changes induced by drought stress in mash plant?

I want to test these leaf dry material with both dry as well as liquid method of FTIR. please i need guidence which solvent will be suitable to test it and how much amount of solvent is required...

11 November 2021 7,090 3 View

Difference Between FEA Result and Hand Calculation in Beam Bending stress and deflection ?

Comparison of simply supported T-beam and beam attached to the shell plate is done. Simply supported T-beam calculations are performed analytically and numerically (ABAQUS software). The beam...

07 November 2021 4,421 4 View

Why is the difference between T-beam (Analytical result) and beam attached to the plate (Abaqus results) ?

I want to compare the T-beam (Analytical solution) to beam attached to the plate with same dimensions (Abaqus result), but there is huge difference between the two results. 1) dimensions and load...

24 October 2021 718 5 View

How to do thousands of dead load analysis together in OpenSees without changing manually??

Hi all, I need some solutions or idea regarding my problem. Hope you people can help me regarding this matter. Please see the below image. At different node, i can assign different point load as...

20 October 2021 9,413 0 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

How to explain the different interaction between soluble and insoluble polymer in water?

Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.

29 July 2024 6,350 3 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

What is the difference between coordination polymer, MOFs, MCOFs?

Wherever I have referred, it puts me in a dilemma about the exact differences between these. It would be really helpful if someone can put me out of this trouble.

21 July 2024 3,045 3 View

Appearance of crystallization peak in heating cycle of DSC test?

For which types of polymers, the crystallization peak in heating cycle of DSC test can be observed and for which types cant? In another word, when this exothermic crystallization can be observed...

18 July 2024 348 3 View

Interpreting ATR-FTIR Spectra for Microplastics Research?

Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...

18 July 2024 7,258 3 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View