How can I simulate the multi-phase (water-air) flow with SPH-element types in Abaqus?

Alireza Khoshkonesh @Alireza_Khoshkonesh

09 September 2017 1 336 Report

Abaqus Lagrangian simulation.

Hi Alireza

This is not exactly an answer to your question but perhaps a hard won knowledge you might want to take a look at - in particular the B/A factor?

http://qringtech.com/2010/09/15/wave-steepening-increase-peak-pressure-piping-pumps/

Sincerely

Claes

Badges
Science topic

More Alireza Khoshkonesh's questions See All

Do you aware of the fundamentals of the philosophy of science in your field?What resources are there for this purpose, especially in engineering?

Philosophy of science

10 November 2017 10,031 6 View

No title

I think USA and west-Europe are good examples of this subject. https://en.m.wikipedia.org/wiki/List_of_countries_by_real_GDP_growth_rate

10 November 2017 8,686 1 View

Do you have any experience in simulation of water unsteady-flow with chaotic dynamic-based code or softewars ?

Chaotic-dynamic applications in water flow, hydraulic, hydraulics structures

10 November 2017 4,163 15 View

What do you think is the fastest way to write a manuscript?

Following order is general and fast: 1.Figures and tables 2.Methods, Results and Discussion 3.Conclusions and Introduction 4.Abstract and title

10 November 2017 7,368 2 View

What do you think about the HAARP? Is there any scientific report about using HAARP for middle east climate changing ?

I think the using HAARP for middle east climate changing is a conspiracy theory, clearly.

10 November 2017 6,985 4 View

What are new research topics on FSI problems?

Fluid-solid interaction, CFD

10 November 2017 6,946 3 View

Can you tell in one sentence, what is the main reason of RG popularity around the world?

RG popularity main reason.

10 November 2017 3,236 4 View

Based on your experience, how do international publishers invest in a book?

Investing on the book, without a fee

10 November 2017 1,130 5 View

Do you know strong, free websites for plagiarism and grammer check? which one is the best?

I searched and find following web-sites: https://smallseotools.com/plagiarism-checker/ http://plagiarisma.net/ https://www.paperrater.com/plagiarism_checker

10 November 2017 3,469 7 View

Do you think RG-DOI is valid, outside the Researchgate website?

https://explore.researchgate.net/dosearchsite.action

10 November 2017 1,382 0 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View