How can I simulate the contact between concrete and CFRP in ABAQUS?

More Mehdi Lima's questions See All

What is the difference in outcome when we use "node to surface" contact instead of "surface to surface" contact in ABAQUS?

Th contact between two surfaces can be modeled as "surface to surface" or "node to surface"in ABAQUS. What is the difference in results when we use these two contacts in ABAQUS standard.

02 March 2015 3,305 1 View

Is it acceptable to increase the thickness of the FRP material in FEM simulation in order to have compatible result with experiments?

Has any body seen in papers or published a paper that an increase in the thickness of FRP material was required in the FEM simulation in order to have a compatible result with experiments? I...

01 February 2015 873 10 View

What is the best method to simulate the FRP-Concrete interface in ABAQUS?

For retrofitting and strengthening purposes of Rc structure, using FRP is one of the common methods. However, the simulation of interface of concrete and FRP is very critical. I would like to...

10 November 2014 1,998 10 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Some new emerging problems on application of RL for scheduling in IoT networks?

I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...

01 August 2024 8,754 2 View

Difficulty with permittivitt and Magnetic Permeability Calculations?

Difficulty with permittivitt and Magnetic Permeability Calculations Hello everyone, I have all the parameters related to the calculations of the permittivitty and magnetic permeability...

30 July 2024 5,206 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View