How can i simulate PaSR combustion model using ansys Fluent for Methane-air combustion?

25 May 2022 0 1K Report

im working on simulating an industrial gas turbine with Partially stirred reactor combustion model using ansys fluent. can anyone help about PaSR model in fluent?

Badges
Science topic

Similar topics
Filing

More Maziar Gheshlaghi's questions See All

Is corn fiber hydrolysis possible without the use of enzymes?

I dont have access to the needed enzymes for CF hydrolysis, so I'm wondering whether I can do the hydrolysis solely with the use of acids? Has it ever been done before?

08 January 2021 1,243 3 View

Modeling of cyber attacks on control systems?

Hi everyone, Are there any references about modeling of cyber attacks on control systems which are discussed deeply. I mean papers or lecture notes or books?I would be thankful if anyone reply...

27 March 2020 8,358 3 View

Could anyone help me on "polyethylene of raised temperature resistance,(PE-RT)"?

I want to know more about polyethylene of raised temperature resistance (PE-RT) and especially its different synthesizing ways. Is it possible to convert HDPE to PE-RT by extruder or it should by...

02 December 2014 2,472 2 View

How do you characterize resin and rosin by FTIR?

How could we distinguish between resin and rosin in an FTIR diagram? Also, how could we calculate the ratio of C5/C9 in resin, by the usage of FTIR?

26 November 2014 5,879 1 View

How can I create a p-polarized gaussian beam in COMSOL 4.3?

I want to simulate refraction of a gaussian beam at Air-anisotropic material interface in frequency domain.

12 April 2014 6,568 1 View

Cyber attack detection vs fault detection?

Hi, Can methods used to diagnose faults in control systems be used to detect cyber attacks in control systems?

01 January 1970 6,738 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View