25 March 2025 1 4K Report

I am working on laser moving heat source model in ansys thermal transient. I got the results like temprature variation of model over time. I need to measure melt pool depth by measuring the depth of isotherm of melting point of material from top and also the temperature gradient plot inside the melt pool. How can I get it?

More Mandar Dodkulkar's questions See All
Where can I find Shear Viscosity and Surface Tension values of Xanthan Gum?

Hello Researchgate community, I am working on my master thesis topic which involves investigation of extensional behavior of liquids. However, I need values like zero shear viscosity, surface...

05 March 2023 377 2 View

How can a nucleic acid aerosol contamination be removed from clean control rooms used to set up Real time PCR assay ?

Hello everyone, I am working on Real time PCR assay. We set up 2-3 PCR assays daily. Though the clean and controls are handled in different biosafety hoods we sometime get internal control...

21 December 2022 1,001 3 View

What I can do for interfacing SBHS (Single Board Heater System) with labview for my project?

Actually I am doing project on SBHS board with SI lab . But I also want to try it with labview.

01 December 2021 4,702 1 View

RNA secondary structure BPSEQ to dot-bracket conversion?

Hello Everyone, Is there any program to convert BPSEQ RNA secondary notation to dot-bracket notation, apart from the RNAPDBee server? I am looking for a program that can be run locally so as to...

24 November 2021 678 0 View

Is a Teledentistry an opportunity in a COVID-19 pandemic?

A need to check different aspects of Teledentistry in COVID-19 situation. A need to discuss on the topic. Reply or feedback on various content of the topic is welcomed.

28 June 2020 9,512 31 View

Can we use Neubauer's chamber for counting diatoms? or counting 'per high power field' is a better techique for diatom counting?

I am working on diatom profiling from a water body where drowning deaths are known recently. Profile includes comparative analysis between different genus of diatoms.

11 February 2016 131 4 View

What is the open channel conductance of BMIM-Cl?

Please, can anyone provide me the literature for the value of open channel conductance ( Not conductivity) of 1 M BMIM-Cl in graphene nanopores having a diameter less than 10 nm?  Thanks in advance.

04 February 2016 7,362 1 View

Which is more accurate approach to calculate ionic current in DNA translocation simulations using GROMACS ?

I am studying translocation of dsDNA poly(AT)45 via graphene nanopore at 0.1080 V/nm electric field in 1 M KCL solution. The production run is performed in NVT ensemble using Nose-Hoover...

31 May 2015 2,702 4 View

How can one assign failure properties of RCC slab in abaqus while analysis?

Hello all, I am analyzing Rectangular RCC slab. While doing the analysis I have managed to assign elastic properties of steel and concrete but couldn't manage to assign plastic or failure...

08 February 2015 1,841 3 View

Can anyone provide me list of well reputed journals (top 10 in terms of impact factor) in civil engineering?

I have worked on structural optimization using MATLAB. Now I want to publish in an International Journal. I thought Computers and structures first. But, I would like to know which would be a...

27 December 2014 7,623 25 View

Similar questions and discussions
Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Melt curve problem in qPCR?

Do these peaks in the curve indicate primer dimer or non-specific products?

01 August 2024 7,466 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close