Can anyone tell me how to plot an average line through some scattered data points (preferable in Origin software).
Please have a look on the example as shown in Graph-2.
I would like to draw a line averaging the points shown in Graph-1.
U might have to fit your data with some order of polynomial wrt your nature of the equation.
Graph -1 represent some experimental data and it looks scattered.
Can you suggest how to find out a polynomial equation to fit the points??
Thanks.
Here is step-by-step tutorial to help with linear fit in Origin:
http://wiki.originlab.com/~originla/howto/index.php?title=Tutorial:Linear_Fitting
and another video:
https://www.youtube.com/watch?v=wsgOnIqOIco
Google is your fiend - search online and you will find lots of help material for Origin :)
@Ray, Thanks for the link.
It helps.
I am preparing triple cation perovskite films using a one-step process (4:1 DMF: DMSO). After the anti-solvent dropping (Chlorobenzene) (5s before the spinning end), the films become transparent...
11 December 2019 7,223 3 View
Due to high electron concentration in a metal or transparent conducting film the NIR transmission falls sharply due to free carrier scattering or plasmon resonance.However, in case of metal NW...
08 September 2018 8,271 3 View
In most of the XRD instrument Cu is used and in most of the XPS instrument Al/Mg is used? Is there any specific reason behind this??
07 August 2018 954 5 View
I would like to deposit film of Yttrium iron garnet using magnetron sputtering technique. Will there be any problem during deposition?? Any risk to the system??
07 August 2018 625 15 View
I would like to know how much ZnO-based TCF (AZO, GZO) contribute (in % or in US$) to the present TCF market and any future forecast??
06 July 2018 767 5 View
If thin films are prepared from a sputtering target that contains three different oxides in same weight percentage (33.3%)..... what might be the XRD of the film look like?? Will it contain all...
03 April 2018 7,482 11 View
Suppose I have two material having high carrier density (hole=5x1022 cm-3 and electron =5x1020 cm-3).. will this two film form good quality diode? Or I can make a diode putting one p and n type...
03 April 2018 2,717 8 View
I would like to prepare thin films of a metal oxide using only wet chemical process (I don't want to involve any vacuum system) to overcoat my existing sample. The process temperature should be...
03 April 2018 9,004 6 View
For metal or doped semiconductor like ITO, FTO, AZO the transmission spectra falls down at visible or NIR region. With increasing electron concentration, one can see the %T graph fall more rapidly...
02 March 2018 6,548 1 View
I would like to know in case of chemical bath deposition process at fixed temperature whether a fast reaction rate would produce more rough surface (high RMS value in AFM) or not. Please site if...
31 December 2017 4,093 5 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....
10 August 2024 8,621 1 View
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,992 0 View
Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...
09 August 2024 7,615 1 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View