How can I perform polymerization of propylene in slurry reactor?

More Ayush Sharma's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

How to enrich pig excreta for increasing nutrient quality organically ?

Pig slurry is rich in major and minor nutrients. Is there any way to improve / Enrich its manure quality to be used in agriculture organically ? please share your knowledge.

09 August 2024 5,605 2 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Leaf area of tomato ?

Hi How can this equation Ln(LA) = 1.038 + 0.89 ln(X) be applied to calculate the leaf area of a tomato? Can you explain with an example and what is the substitution of Ln and ln?

06 August 2024 2,508 2 View

Why did the authors extrapolate a phenotype that they experimentally proved in one bacterial strain across the whole genus of the organism?

I aim to be as skeptical as possible regarding whether a pair of orthologous genes results in the same phenotype in their different but related bacterial organisms under similar environmental...

05 August 2024 6,787 4 View

How to preform densitometry on SDS-page bands?

I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...

05 August 2024 9,805 3 View

XRD Analysis is showing only Calcium carbonate. It is not showing other compounds. Can anyone help me get the other compounds?

XRD Analysis is showing only Calcium carbonate. It is not showing other compounds. Can anyone help me get the other compounds

04 August 2024 3,019 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

How to explain the different interaction between soluble and insoluble polymer in water?

Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.

29 July 2024 6,350 3 View

Why is it not common to see similar pairs in polymer sliding pairs?

If the pairs are similar, will it reduce the adhesion due to electric charges?

29 July 2024 3,185 2 View

HAs anyone used TGA to find activation enegy of water evaporation?

I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....

28 July 2024 9,545 6 View

Interpreting ATR-FTIR Spectra for Microplastics Research?

Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...

18 July 2024 7,258 3 View

How does surface energy affects the solidification of polymer?

Dear All, I would like to ask about the relation between the surface energy and solidification of polymer. If we apply a chemical treatment such as NaOh solution or silane treatment on the...

17 July 2024 190 3 View

I need to know the required time for VDF heating with water for 50-80°C for PVDF Polymerization in ?

i need to know the required time

15 July 2024 4,796 2 View

Nizar Matar

I hope that the 3 references given in the link will be helpful. The 3rd one talks about the mixer (or agitator) which is 45o pitched 4-blade turbine with a maximum speed of 3,000 rpm.

My regards.

http://www.pse.umass.edu/sites/default/files/coughlin/documents/Kinetic%20Modeling%20of%20Slurry%20Propylene%20Polymerization%20using%20rac-ET.pdf

Article Propylene polymerization in a semibatch slurry reactor over ...

Mushtaq Ahmad

Review on Development of Polypropylene Manufacturing Proces, may be useful