What is (response surface graph)?

For optimization of reaction conditions, most of the time we have several factors to take care of, like pH, temp, initial conc., ionic strength... etc. How we can express in a professional way our...

27 May 2020 3,150 3 View

For a hydrothermal autoclave, can we use a glass container instead of the teflon?

To increase the temperature of the autoclave higher than 160 or 200 C, we need thermally stable materials as the reaction container. So what kind of materials can be used??

17 May 2020 8,963 7 View

Can I use matlab deep learning toolbox for regression problems?

Hi everybody I want to use MATLAB deep learning toolbox to relate the activity (pIC50) of molecules to their molecular descriptors. Can I use convolutional neural network with a regression layer...

03 February 2020 1,874 6 View

How to determine the degree of similarity between two signals?

I'v been doing an investigation about detection of a specific signal and I need to determine that how a received signal resembles the reference signal. A primary approach to this problem is done...

06 November 2017 6,369 7 View

How we can apply FRP in Concrete beam with Abaqus?

Hello all, I want to modelling a Concrete Beam with ABAQUS, My intention is that first beam cracked and then the FRP, apply to beam and analysis continue. can you help me?

11 January 2017 8,962 6 View

How can we determine representative volume element length (Lrve) for concrete?

for periodic materials, determining Lrve is simple but for a non-homogeneous material such as concrete, it is not that simple. any advice such as methods, references, etc. would be appreciated.

04 November 2016 6,044 3 View

How can i do a meta-analysis of a subject in sport and physical education?

I want to learn about this type of research.

11 January 2014 9,954 3 View

The internal energy change for isothermal processes is zero. But for the vaporization of liquid (which is an isothermal process) it is not zero.

The internal energy change for isothermal processes is known to be equal to zero. But in the case of liquid vaporization (e.g. liquid water to steam) (boiling at constant temperature), the...

01 January 1970 7,917 4 View

Why some Cr(III) complexes have labile reactions ??

01 January 1970 7,787 7 View

I am interested in medicinal chemistry field, which books are highly recommended to learn from?

I am at the beginner level in drug design and drug discovery, and I am interested to learn more about this field. Which books are highly recommended to start from and gives me all essential...

02 March 2021 8,437 2 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View

Access to supercomputer resources in India?

Hello everyone, I want to perform some gaussian calculations and want to use Materials studio for my research work. Can anyone guide me how to get access to supercomputer resources in India for...

15 February 2021 8,264 3 View

Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View

Is it possible to get compass potential paramters from MATERIALS STUDIO 6.0?

Hi all, I wonder whether we can get potential parameters from material studio. I have a licensed version available. If I use polymers and cnt in materials studio to perform MD simulations,...

03 February 2021 7,673 3 View

Can I heat my ELISA at 37C?

Hello, I am conducting a sandwich-type ELISA. It is to see if small molecules can interfere with a protein-protein interaction. As this interaction would occur in the human body, may I heat...

31 January 2021 4,271 3 View

Submission of the Materials Studio jobs to the remote Linux cluster?

I am doing some simulations using the Forcite module in Materials Studio. As the speed of this calculation on my workstation computer is unacceptably slow, I am trying to submit my job to the...

14 January 2021 8,653 1 View