How can I make FE model of multi layerd woven CFRP with ANSYS?

More Mahyar Pourhassan's questions See All

How can I use circlefit method with mobility by matlab?

03 April 2016 6,114 1 View

How can I ignore rigid body motion in ansys apdl?

03 April 2016 8,142 0 View

How can I identify energy of impact to plate with power spectural density?

31 December 2015 8,718 2 View

Can any one help me howcan i measure numerically the energy of impact via FRF(Frequency Response Function)?

FEM modeling

10 November 2015 2,903 2 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View