How can I incorporate Managed Aquifer Recharge (MAR) into a MODFLOW model with GMS as GUI?

29 March 2021 0 8K Report

Managed aquifer Recharge techniques are being used for groundwater development. Efficiency of those techniques can be assessed by numerical modeling. How can we incorporate MAR into a MODFLOW model with GMS interface??

Badges
Science topic

Similar topics
Analytical Chemistry
Column

More Sayedul Kibria's questions See All

Why having very high value of LST (Land Surface Temperature) after calculating from the (LANDSAT/LC08/C02) LandSat 8 collection 2 level 2 tier 1 data?

I have used the formula LST = (BT / (1 + (0.00115 * BT / 1.4388) * Ln(ε))) for finding the JJA (June, July, and August) LST for California. Where for BT (at satellite brightness temperature) I...

27 May 2024 7,680 2 View

Is the early arrival of a migratory bird to its breeding or feeding ground an adaptation to climate change?

Is the early arrival of a migratory bird to its breeding or feeding ground an adaptation to climate change? Can we call these early arrival birds a positive match to climate change?

07 March 2024 5,174 4 View

Which pollutants are most threatening to birds' lives concerning lethal and sub-lethal impacts?

Which pollutants can threaten birds' lives concerning lethal and sub-lethal impacts among the following: Toxic heavy metals, Organochlorine pesticides, Plastics/microplastics, Oil/ petrochemical...

18 December 2023 9,040 11 View

Simple linear regression conflict in SPSS and STATA?

Hi everyone Can someone help with the following observation while applying simple linear regression in SPSS and STATA Dependent variable: Ferritin levels (ng/ml) Independent: Age of the respondent...

05 December 2023 7,176 3 View

What is the conversion factor for the wet weight to the dry weight of a biota sample contaminated with heavy metals or pesticides?

What is the conversion factor for the wet weight of a biota sample (e.g., birds, mammals) to the dry weight of a biota sample contaminated with heavy metals or pesticides? Please provide any...

23 November 2023 4,162 0 View

Are microplastics a threat to your country?

Microplastics (MPs) are small plastic particles that are less than 5 mm in size. MPs can contaminate air, soil/ sediments, water, food (fisheries and agriculture) and human health. Do you face any...

12 September 2023 5,862 3 View

How could we support research scientists who cannot purchase environmental books?

Climate change and pollution are global problems and concerns. However, poor research scientists and the grassroots community from developing countries may not have the ability to purchase...

28 June 2023 6,563 2 View

How can I draw two graphs in a single plot?

I have two sets of data. Dataset 1. Proportion of respondents wanting smoke-free housing: Yes =586 (95.1%), No= 30 (4.9%). Dataset 2. Among these 586 respondents, 262 (44.7%) preferred a...

09 February 2023 1,240 5 View

Why A431 cell are not detached from the cell culture plate after trypsinization?

For the first time, I am culturing the A431 cell. After trypsinization, I have noticed that almost all of the cells are not detached. For trypsinization, I used 0.5 trypsin 0.53 EDTA and kept the...

11 June 2020 3,443 3 View

Can face-masks made of green leaves help against coronavirus?

People in poor countries cannot afford to purchase facemasks. Some tribal and rural people living in remote locations currently uses masks made of plant leaves as an alternative. Would facemasks...

23 April 2020 8,922 14 View

Do the simulated heads show an increasing trend or does the model require spin up?

I ran Modflow using a 2005 engine over my study area and got my first results. The result at one such location is attached herewith. There is a difference between simulated and observed time...

08 May 2024 6,551 0 View

Why do I get this error: "forrtl: severe (24): end-of-file during read, unit 68" from the .BT3 file and how do I solve it in visual MODFLOW Flex?

Hello everyone, while trying to run a Visual MODFLOW Flex model I get an error information regarding the .BT3 file. Error Information: forrtl: severe (24): end-of-file during read, unit 68, file...

19 April 2024 4,172 0 View

Where does the calcium in travertine comes from?

Travertine is common to see in hot spring, its main component is calcite. The solubility of calcite decreases with increasing temperature, and seems CO2 degassing makes calcite harder to deposit....

11 March 2024 2,030 5 View

How to give aquifer properties in modfloflex when we have more number of grids ?

- In conceptual model of visual MODFLOW flex, how to give or change the cell properties (Hydraulic conductivity, specific storage, etc) zone wise for every grid, when we have more number ( i.e.,...

16 February 2024 9,085 0 View

Hydro position in france?

INRAE is recruiting a researcher for the the joint research unit (INRAE-Avignon University) EMMAH (Environnement Méditerranéen et Modélisation des Agro-Hydrosystèmes https://umremmah.fr/) based in...

31 January 2024 8,263 0 View

Modelmuse: Modflow 6: Why Wells not showing at correct depths location?

I have imported wells as points and filled in the Data (i.e., X, Y, Z, etc.---using the Well Package) The well locations appear on the Top View, but the depth is not showing up even though...

25 January 2024 9,145 0 View

MODFLOW: How to efficiently modify existing 3DGrid using GMS?

I work on a MODFLOW Model using GMS to simulate subsurface water exchanges between a small straightened stream and its heavily modified alluvial plain. I’m looking for efficient methods to modify...

09 January 2024 708 0 View

Why am I getting an error while running Modflow in steady state ?

I am trying to set up groundwater flow model over the Ganga Basin (0.4 million sq km) using Modflow. I am using Visual Modflow Classic and Modflow 2005 engine. I had set up the transient model but...

04 December 2023 905 3 View

How I can restore factory values for Plot wizard is GMS?

Hello Please how I can restore factory values for GMS because I have a display problem in the plot. I can't choose between bare or line in parameter sensitivity.. Also I have a problem with...

15 October 2023 3,876 0 View

PEST option error in MODFLOW?

In MODFLOW when I run the PEST option I encounter this error. Anyone has an idea?

12 October 2023 5,854 2 View