How can i find JMAK parameters for pure Mg?

More Kiarash Mashoufi's questions See All

What can i do with an oxidated die ?

Hi , I've made an ECAP die out of H13 tool steel . After doing a hardening heat treatment in 1000C and quenching in air , i have a thin film of oxidated steel on it . It makes my surface very...

22 December 2019 9,318 2 View

Deform 3D grain size simulation?

hello everyone I'm working on SPD process and I have a new method based on compression and expansion in extrusion which results in decreasing grain size . I want to use Deform 3D and Avrami DRX...

15 October 2019 3,403 1 View

Displacement boundr condition problem in Abaqus ?

Hi , Recently i'm working on simulating an extrusion process I use Abaqus explicit temp-displacement coupled step . My model contains 3 parts , a rigid die and a rigid punch and a deformable...

10 April 2019 1,472 2 View

Under what culture conditions for Pseudomonas Putida, motility of the bacteria is ensured (Medium, temperature, time...)?

I am using LB Broth (25 gr in 1L) and Incubating the samples for 24 hours in 25 degrees Celsius. I put the culture tubes on a shaker with 300 RPM for the first twelve hours but still, what I see...

22 January 2018 7,426 3 View

I want to intervene a kind of growth factor in MCF-7 cell line for 72 hours without FBS, is it possible?

I use serum replacement as a substitute for FBS in my experiment.

05 December 2015 1,057 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

Has anyone used deep learning for 2D/3D REGISTRATION ?

I am a Master student in Biomedical (Bio-electrical) Engineering and work on " 2D-3D registration ( CT and X-Ray) as my thesis. I created DRR from CT and want use CNN( Convolutional Neural...

19 February 2021 6,354 3 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

Which Journals would you advise to submit a Letter which briefly talks about neurosurgical treatment of neuro-oncological patient during Sars-COV-2?

Possibily not an open access journal which does not add any publishing costs once being accepted. Thank you in advance

09 February 2021 717 6 View

Cause of slow bromophenol blue migration and smearing while running SDS PAGE?

While running gels for western blotting, I am currently getting, what seems to be, the blue dye from my sample buffer migrating more slowly in sample lanes leaving blue streaks. These transfer to...

08 February 2021 5,317 3 View

Background and spots in Western Blot membrane?

Do you know why my membrane looks like this? I did this western for Anti-hnRNP D/AUF1 antibody ab50692, as primary antibody in 1:1000 overnight at 4c and Anti-rabbit IgG HRP linked antibody...

07 February 2021 5,591 4 View

ACE2 Blotted as a double band?

Hello, I have recently run a western of Vero cells for ACE2. I detected ACE2 at the correct size, but it presents as a double band. The sample was prepared by lysing cells in 1X Laemmli...

07 February 2021 6,973 3 View

Why can't I get an Sdr value when measuring surface texture parameters?

I am performing a texture surface analysis of a polished ceramic surface using an optical profiler; amongst the parameters I am measuring is the Sdr. I got values for the Sdr when I analyzed my...

25 January 2021 4,462 3 View

Reza Darvishi Kamachali

well, there numerous materials on the subject.. e.g. Article Recrystallization and grain growth of deformed magnesium alloy

The JMAK inputs are all related to the intrinsic properties of materials, one can also make some approximation of them

Kiarash Mashoufi

Reza Darvishi Kamachali thank you for responding .

are JMAK inputs defined by experiments or they can be measured by FEM simulations ?

and by the way , do you have any experience on using Deform 3D JMAK model to measure the grain sizeof a metal after a plastic deformation ?

Darlan Vale Bayão

Hello Reza Darvishi Kamachali and Kiarash Mashoufi

I'm new to the drawing process and I'm looking for the software Deform 3D to conduct some analysis in my research.

I would like to know where I can find the software to download for free?

Someone here has the installation file of Deform 3D to share with me?

Thanks in advance!