How can I draw a axial velocity with respect to r (at constant cross section) in tecplot?

More Amirhosein Bashiri's questions See All

Which demand generation method is suitable in SUMO traffic simulator?

I wish to simulate a scenario in SUMO as follows: I wish to define some vehicles that are randomly located in a residential area on the network, and then these vehicles will move to their...

25 November 2020 3,196 2 View

Is it possible to generate the same scenario in MATSIM Simulator?

As far as I know, the same plan might create different events when executed multiple times in MATSIM. But, I am looking for a way that whenever I run a particular scenario for my agents, the...

13 November 2020 8,544 1 View

Capability of MCNP6 in Muon tracking?

Is MCNP6 able to simulate galactic cosmic ray specifically Muons ? if yes does it have any energy or cross section restrictions?

16 June 2020 9,049 3 View

What are the recommendations for prevention of research misconduct in universities?

There are many recommendation to foster research integrity and some are initially for research institutions and universities. Can you introduce some document about it?

13 February 2020 8,173 2 View

Invited to cooperate/?

Hello to all dear researchers. 2 of my friends and me from university of Tehran (Iran) have written a review article about " Adipokines ". We need to modify the article and publish it, with the...

07 August 2018 1,646 5 View

Question about permission?

Hello to every one. How can i get the E-mail address of Journals?Thank you for answer

19 July 2018 7,062 9 View

Does anybody know about carbon nanotube concrete in radiation shielding?

I want to know does carbon nanotubes have an effect on shielding properties of concrete?

13 March 2016 4,009 2 View

Can anyone help me with "negative eigen value" error in Abaqus that occurs because of buckling in opposite side in cyclic loading?

i'm modeling a plate in abaqus under cyclic loading and i faced with "negative eigen value" error that occurs because of buckling of plate in opposite side.

11 March 2016 5,265 3 View

How can i put a special accelaration spectrum to a model in abaqus ?

For example in " Etabs" we can put accelaration spectrum in a text file and import it to the application or some other ways but i dont know how can i do it in abaqus . . .

18 July 2015 1,631 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

S . Shukla

It can be simply done in three steps, I assume you already write the necessary data files from the solver. So, the first thing in the beginning is you have to change the co-ordinate system into cylindrical co-ordinate and take a slice at appropriate cross section finally go to the plot and select the particular variable by drop down the list of all variables (axial velocity, radial velocity, pressure etc.)

Amirhosein Bashiri

thank you shrish.

did you know how to transform coordinate from cartesian to toroidal in tecplot?