Is it possible to generate the same scenario in MATSIM Simulator?

Amirhosein Adavoudi Jolfaei @Amirhosein-Adavoudi-Jolfaei

14 November 2020 1 9K Report

As far as I know, the same plan might create different events when executed multiple times in MATSIM. But, I am looking for a way that whenever I run a particular scenario for my agents, the output will be the same. By output I mean, for example, the time when the agents arrive at their work or the time when they depart the traffic lights. I am wondering if it is possible to do so by means of seeds in MATSIM?

Daniel Wesemeyer

Hi Amirhosein,

running a MATSim scenario with the same inputs using the same seed in multiple runs should yield reproducible results regarding e.g. travel times, arrival times. This is, of course, only valid if you don't use replanning strategies that adapt routes, departure times or activity locations.

Best regards,

Daniel

Badges
Science topic

More Amirhosein Adavoudi Jolfaei's questions See All

Which demand generation method is suitable in SUMO traffic simulator?

I wish to simulate a scenario in SUMO as follows: I wish to define some vehicles that are randomly located in a residential area on the network, and then these vehicles will move to their...

25 November 2020 3,196 2 View

What are the recommendations for prevention of research misconduct in universities?

There are many recommendation to foster research integrity and some are initially for research institutions and universities. Can you introduce some document about it?

13 February 2020 8,173 2 View

Invited to cooperate/?

Hello to all dear researchers. 2 of my friends and me from university of Tehran (Iran) have written a review article about " Adipokines ". We need to modify the article and publish it, with the...

07 August 2018 1,646 5 View

Question about permission?

Hello to every one. How can i get the E-mail address of Journals?Thank you for answer

19 July 2018 7,062 9 View

How can I draw a axial velocity with respect to r (at constant cross section) in tecplot?

15 September 2015 2,972 2 View

How can i put a special accelaration spectrum to a model in abaqus ?

For example in " Etabs" we can put accelaration spectrum in a text file and import it to the application or some other ways but i dont know how can i do it in abaqus . . .

18 July 2015 1,631 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View