How can I couple my DEM results with ANSYS Fluent?

11 October 2019 0 899 Report

I have modeled a spreader by using DEM with the help of EDEM. Now I want to couple those results with ANSYS fluent for performing CFD analysis.

Would you please suggest me the way to do the same?

More Kuldeep Mandloi's questions See All

Homogenous catalyst recovery?

Dear Friends, Please suggest, How much recovery possible for Homogenous catalyst? And share supporting literature if available. Best regards Kuldeep

24 July 2023 3,626 1 View

Why there is volume expansion in alloying anodes in sodium ion battery?

23 June 2023 617 3 View

Which antifungal agents (antibiotic ) used in media for isolation of bacteria from soil?

isolation of rhizobacteria from turmeric rhizomes but there is the contamination of fungus.

31 January 2023 7,492 2 View

Dopamine based adhesion for wet surfaces?

I have used dopamine hydrochloride solution: 2g/L of 10 mM Tris-HCL (pH=8.5) buffer for dip coating certain surfaces such as PDMS for around 24 hours while stirring slowly. The solution changes...

22 December 2022 1,759 4 View

How can I draw Fukui functions (f-, f0, f+) using Gaussian software?

Using Gaussian software, how can I draw Fukui functions (f-, f0, f+)? DFT Simulation, Quantum chemistry, Gaussian,

19 December 2022 8,735 3 View

After opening an PIKOVASKAYAS media of Hi media turned black although it is tightely packed may i use this ?

working on the isolation of phosphate solubilizer by the use of Pikovaskayas media but after some days it was turned black although it was tightly packed what should i do

25 November 2022 9,398 2 View

How much concentration of Flucanazole added in media to isolate bacteria?

want to isolate rhizobacteria from soil and hence required fungal growth inhibition hence need to add flucanazole in media

18 November 2022 9,743 2 View

For my thesis writing, can i select my topic from outside of my stream?

Dear Researchers, Greetings!!! I'm in my initial stage of topic selection for my thesis and i want to take the topic which is integrated with another subject area (as i'm from Computer stream...

10 November 2022 5,033 1 View

Which antifungal agents (antibiotic ) used in media for isolation of bacteria from soil?

I am working on isolation of PGPR from the turmeric plant but fungal growth contaminates and bacterial isolation is not done properly.

26 August 2022 7,408 3 View

If occupancy in Rietveld refinement is not in proportion to the compound then is it wrong?

I have performed Rietveld refinement of a compound (A2B2O7), all parameters are in good range but Rp value is high (approx 40) and the occupancy is also not in proportion to the compound however...

11 May 2022 725 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Should I include H atom into C3N5 when i am doing DFT modelling?

Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...

07 August 2024 8,414 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View